background image

IES PR-6 dimmer pack Operators’ Manual v. 1.1         25-04-2002 1 

 

 

 

Operator Manual 

 

PR-6 rack mounted 

dimmer pack 

 

 

 

 

 

 

 

 
 
 
 

on

dmx

DMX

INST

CHAS

PWR

MAN

CONF

INFO

CHK

EXIT

ENT

L                                                           D : 0 0 1 *

C H     1     2     3     4     5     6     A : 0 1 6 *

 

 

 

Contents: 

1 Introduction......................................................... 2 

1.1 Product range............................................ 2 
1.2 Main features of PR-6............................... 2 
 

2 Unpacking and installation................................. 2 

2.1 Unpacking & checking .............................. 2 
2.2 Positioning ................................................. 2 
2.3 Connections .............................................. 2 
2.4 Safety......................................................... 2 

3 Control panel layout........................................... 3 

4 Function overview .............................................. 4 

4.1 Maximum and minimum levels................. 4 
4.2 Response speed ....................................... 4 
4.3 Non-dim operation .................................... 4 
4.4 Local control .............................................. 4 
4.5 Dimmer curves .......................................... 4 
4.6 Status reporting......................................... 4 
4.7 Backup settings......................................... 4 

5. Information displays and manual control ......... 4 

5.1 To check dimmer performance ................ 4 
5.2 To check software versions...................... 4 
5.3 To manually control a dimmer level ......... 5 
5.4 To operate the chaser............................... 5 

6 Programming...................................................... 5 

6.1 Flow diagram............................................. 5 
6.2 General Programming Advice .................. 5 
6.3 Front Panel Controls ................................. 6 
6.4 General controls ....................................... 6 
6.5 DMX programming.................................... 6 
6.6 Serial address ........................................... 7 
6.7 Maximum & Minimum levels..................... 8 
6.8 Response time .......................................... 8 
6.9 Dimmer curves .......................................... 9 
6.10 Non-Dim operation.................................. 9 
6.11 Start Mode............................................... 9 
6.12 Passwords ............................................ 10 
6.13 Sleep mode ........................................... 11 
6.14 Fault reporting ....................................... 11 
6.15 Return to factory settings...................... 11 

7. DimSTAT ......................................................... 12 

8. Fault finding..................................................... 12 

8.1 Reported faults........................................ 12 
8.2 First line maintenance............................. 12 

9. Specifications .................................................. 13 

10. Declaration of conformity.............................. 14 

11. Flow chart ...................................................... 15 

12. Index .............................................................. 16 

Summary of Contents for PR-6


















Reviews: