www.ingenico.com
28-32, boulevard de Grenelle, 75015 Paris - France / (T) +33 (0)1 58 01 80 00 / (F) +33 (0)1 58 01 91 35
Ingenico - SA au capital de 47 656 332 / 317 218 758 RCS Nanterre
LANE/8000
900028753 R11 000 01/1216
Copyright© 2016 Ingenico
All rights reserved
www.ingenico.com
28-32, boulevard de Grenelle, 75015 Paris - France / (T) +33 (0)1 58 01 80 00 / (F) +33 (0)1 58 01 91 35
Ingenico - SA au capital de 47 656 332 / 317 218 758 RCS Nanterre
Changes or modifi cations to this device not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Any liquid spill under the custom cover must be removed right away.
The main port at the back must not be used to connect a standard video HDMI cable. Only connect cables provided by
Ingenico.
4_
Environment
This product is labelled in accordance with European Directive 2002/96/EC concerning Waste Electrical and Electronic Equipment
(WEEE).
Ingenico ensures that effi cient collection and recycling schemes are set-up for WEEE according to the local regulation of your country.
Please contact your retailers for more detailed information.
Packaging waste must also be collected separately to assure a proper disposal and recycling.
Please note that proper recycling of the WEEE will ensure safety of human health and environment.
More Information
For more information on cleaning, troubleshooting, operating the device, features, specifi cations, accessories, the system menu,
security, and downloading see the
Ingenico Lane/8000 User Guide.
5_
Terminal Location
The Lane/8000 device may be mounted on a fl at surface, wall, or customer stand (recommended).
The device is designed to operate in the following environment:
Operating temperature of 0°C to 45°C
Operating humidity of 10% to 85% RH non-condensing
The terminal is intended for internal use only.
Do not place the Lane/8000 device on a PC monitor, adjacent to an electronically active security tag deactivation
system, or near other sources of magnetic fi elds.
The Lane/8000 device must be at least 12 inches away from an electronically active type of security tag deactivation
pad.
There are two types of security tag deactivation systems :
An electronically active system sends out a powerful and potentially disruptive signal to deactivate the security
tag. If the Lane/8000 device is placed too close to the system’s pad, or placed above the pad, the signature capture
fi les may be corrupted.
A passive system is a permanent magnet type that does not send out a signal. This type does not affect the
Lane/8000 device.
Lane/8000
Installation Guide
The CE marking is the manufacturer’s declaration that the product meets the requirements of the applicable EC
directives. The CE mark is a mandatory conformity marking for certain productssold within the European Economic
Area (EEA).
The RCM mark will be the only mark to indicate compliance with the Australian Communications and Media
Authority’s (ACMA) regulatory arrangements for telecommunications, radio, EMC and electromagnetic energy
(EME).
Waste of Electrical and Electronic Equipment (WEEE) symbol indicates that when the end-user wishes to discard
this product, it must be sent to separate collection facilities for recovery and recycling. By separating this product
from other household-type waste, the volume of waste sent to incinerators or land-fi lls will be reduced and natural
resources will thus be conserved.
This TÜV symbol shows consumers at a glance that a product has been examined by neutral experts and that there
are no safety concerns
The UL mark appears on end products and complete components suitable for factory and fi eld installation.
All of the products carrying these marks are coveredby our Follow-Up Services program to determine that products
continue to be manufactured in compliance with UL’s safety requirements.
The C-Tick is an identifi cation trademark registered to the Australian Communications Media Authority (ACMA). The
C-Tick mark signifi es that the labelled electronic device is compliant with applicable electromagnetic compatibility
(EMC) requirements
FOR PLUGGABLE MODULE, the socket-outlet shall be installed near the equipment and shall be easily accessible.
