background image

HIGH PRESSURE 

MATERIAL REGULATOR

OPERATOR’S MANUAL 

651785

INCLUDING: OPERATION, INSTALLATION AND MAINTENANCE

RELEASED: 7-20-14

REVISED: 11-8-17 

(REV: B)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING, 

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

 (800) 495-0276 

 FAX (800) 892-6276 

© 2017                   CCN 47522184001 

arozone.com

SERVICE KITS

 

y

Use only genuine ARO

R

 replacement parts to assure 

compatible pressure rating and longest service life.

 

y

Fluid diaphragm kit 61962-1 can be ordered separately 

(see page 4).

SPECIFICATIONS

Model Series  . . . . . . . . . . . . . . . . .  651785

Type   . . . . . . . . . . . . . . . . . . . . . . . . .   Downstream

Material Inlet 

(female)

  . . . . . . . . .  3/8 - 18 NPTF - 1

Material Outlet 

(female)

  . . . . . . .  3/8 - 18 NPTF - 1

 Dimensional Data . . . . . . . . . . .   see page 8

PERFORMANCE DATA

Regulated Pressure Range . . . . . . .  75 - 450 psig (5.2 - 31.1 bar)

Maximum Regulated Pressure  . .  450 psig (31.1 bar)

Maximum Inlet Pressure . . . . . . . . . . 3000 psig (206.9 bar)

Maximum Temperature Limits . . .  0

_

to 200

_

F (-18

_

to 93

_

C)  

Figure 1

Summary of Contents for 651785









Reviews: