background image

Instruction Manual

P/N:EVO7006

Vehicle Application:

Make:

Chevrolet /GMC

Model: 

Silverado / Sierra 

2500/3500

Year:

2015

Engine:

6.6L (TD) Duramax LML

EXPLODED VIEW

Page 1 EVO7006

TOOLS REQUIRED

• 10mm Ratchet & Socket

• 8mm nut drive

• Allen key

• Flat Blade Screwdriver

• Phillips Screwdriver

A Limited Lifetime Warranty to the original purchaser against defects in material and workmanship on all Injen intake systems excluding the filter element.

 

Any and all warranty coverage is limited to the repair or replacement of the defective part only, at Injen Technology’s discretion. The warranty does not

 

cover incidental or consequential damages, nor does it cover the cost of installation or removal of the defective part or its replacement. Proof of purchase

 

is required. 

Report any defective or missing parts to the authorized Injen dealer you purchased this product from. Before installing any parts of this system,

please read the instructions thoroughly.  If you have any questions regarding installation, please contact your Injen Technology dealer. Installation

DOES require some mechanical skills.  A qualified mechanic is always recommended.

WARNING: 

FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PRO-

VIDED HARDWARE MAY DAMAGE THE INTAKE SYSTEM, ENGINE AND COMPONENTS!!!

*Do not attempt to install the intake system while the engine is hot.

Severe burn could result from touching hot engine components!

A

B

C

D

E

F

G

H

I

J

K L

M

N

O

Item QTY.

P/N

Discription

A

1

#15054 Rotomold Tube

B

1

#15055 Rotomold Plenum

C

1

#15056 Rotomold Box

D

1

#1068

6.00" Filter

E

1

#3201

5.00" Hump Hose

F

1

#3163

4.25"- 4.50"Straight Hose

G

2

#4014

#72 Clamps

H

2

#4019

#80 Clamps

I

4

#6047

M4X10mm Button Head Bolts

J

1

#6095

M6X80mm Bolt

K

3

#6096

M6x30mm bolt

L

4

#8047

Rubberized  washer

M

1

#15040 Filter Monitor

N

1

#3198

3mm-16" Vacuum Hose

O

1

#8026

Grommet

Summary of Contents for EVOLUTION EVO7006

Page 1: ... Injen dealer you purchased this product from Before installing any parts of this system please read the instructions thoroughly If you have any questions regarding installation please contact your Injen Technology dealer Installation DOES require some mechanical skills A qualified mechanic is always recommended WARNING FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PRO VIDED HARDWA...

Page 2: ... we like to call it helps trap smaller particles and protect your engine NOTE DISCONNECT BATTERY BEFORE INSTALLATION To Clean your filter Carefully remove the filter from the housing Once removed wipe down the housing using a clean shop towel being careful not to knock any dirt and or debris in the air inlet Your filters can be cleaned by carefully vacuuming the filter media from the dirty side or...

Page 3: ... 6 to the barbed fitting on the fil ter 6 Place the filter onto the the Injen in take plenum and then secure the clamp 9 Remove the 10mm bolt from the support bracket and then swing the support bracket towards the right This will allow you to install the Injen air box 12 Place the 4 25 4 50 step hose and two 72 clamps onto the turbo inlet Tighten the clamp on the turbo inlet side for now 11 Lower ...

Page 4: ...orrect the problem 5 Check the filter for excessive dirt build up Enjoy the added power and performance of your new intake system Congratulations You have just completed the installation of this intake system Period ically check the alignment of the intake nor mal wear and tear can cause nuts and bolts to come loose Note Check clearance and adjust if needed Failure to check the alignment and adjus...

Reviews: