background image

3.21.17 05373D © Inovonics, 2017 - www.inovonics.com

EN1702 Current/Voltage Data Transmitter

Installation Instructions

1 Overview

The Inovonics EN1702 current/voltage data transmitter offers the flexibility 
of an Inovonics universal transmitter, with out-of-the-box compatibility for 
both voltage and current analog sensors, to support a variety of data 
logging applications. The EN1702 current/voltage data transmitter can be 
used to wirelessly monitor and measure conditions including differential 
pressure, tank level, gas and volatile compound levels, extremely high and 
low temperatures, current consumption, and more. 
The EN1702 current/voltage data transmitter must be used with the 
Inovonics EN4000 serial receiver or EN6040 network coordinator, and 
requires an application designed to support advanced functionality.

1.1 Inovonics Contact Information

If you have any problems with this procedure, contact Inovonics technical 
support:

• E-mail: support@inovonics.com.
• Phone: (800) 782-2709.

1.2 EN1702 Internal Components

 Figure 1  

EN1702 internal components

1.3 What’s In The Carton

• Three wall mount screws.
• Three wall mount anchors.
• Two selection jumpers.
• One piece of mounting tape.
• One 3.0V lithium battery.

2 Installation and Startup

2.1 Installation Notes

• These products are designed to be installed and maintained by 

professional technicians.

• Products are intended for indoor use.
• Manually test all products weekly.

2.2 Install the Battery

1.

Pry the top lip of the mounting bracket up, and lift the bracket off of the 
transmitter.

2.

Use your thumb to depress the housing release tab; separate the 
housing.

3.

Install the new battery.

4.

Press the reset button to initialize the transmitter. If replacing a battery, 
the transmitter’s most recent programming will be restored upon 
initialization.

2.3 Select the Frequency Band

EchoStream products are able to use a range of radio frequencies, and 
must be configured for your geographic area. This product ships with a 
default frequency range of 902-928 MHz for use in North America. If you 
are using the product in North America, skip to section 2.4, “Attach the 
Analog Sensor(s) and Select Input”; if you are using the product in Australia 
or New Zealand, you will need to configure the transmitter.

5.

Place a selection jumper on the appropriate frequency band selection 
pins.

• Place the jumper on the left two pins, marked NZ, to set the frequency 

range to 921-928 MHz for New Zealand.

• Place the jumper on the right two pins, marked AU, to set the 

frequency range to 915-928 MHz for Australia.

6.

Press the reset button to complete configuration.

Caution: 

When pressing the reset button, make sure you don’t also touch 

the frequency band selection pins. Touching the frequency band selection 
pins while pressing the reset button can inadvertently set the current/
voltage data transmitter to the wrong frequency band.

2.4 Attach the Analog Sensor(s) and Select Input

The EN1702 current/voltage data transmitter is compatible with the 
EN4000 serial receiver and EN6040 network coordinator, and requires an 
application designed to support advanced functionality.
Inovonics has tested the following analog sensors for compatibility.

• Carbon dioxide (CO): Kele® Model CD-A carbon dioxide sensor; 

Omega Engineering® TXCO-50 series carbon monoxide transmitters.

• Relative humidity: Omega Engineering HX71 series relative humidity 

sensor/transmitter.

• Temperature: AutomationDirect® ProSense® head mount RTD 

temperature transmitters; Omega Engineering TX-M12-RTD series 
RTD transmitters.

• Thermocouples: Jumo® mineral-insulated thermocouple with bare 

connection wires to DIN 43710 and DIN EN 60584 (901210); RS Pro® 
thermocouple and extension wire type N 2 Core PVC sheath 100m.

• Differential pressure: Omega Engineering PX274 or PX277 series 

differential pressure transmitters.

• Pressure transducer: Omega Engineering PXM309 series industrial 

pressure transducers.

• Volatile organic compounds (VOC): Rae Systems® RAEGuard 2 PID 

detector.

To confirm compatibility with other analog sensors not listed, please contact 
Inovonics technical support.

For product and installation videos visit us at 
www.inovonics.com/videos or use the QR 
code below.

A

First external sensor 
terminal block

B

Second external sensor 
terminal block

C

Sensor input 
selection pins

D

Frequency band 
selection pins

E

Reset button

F

Battery

G

Programming 
header

H

Housing release tab

A

B

E

D

F

C

G

H

Reviews: