background image

Inspire Home Automation

www.inspirehomeautomation.co.uk
contact@inspirehomeautomation.co.uk
01202 798390

1

1

NS1003 Installation Guide 

Rev 1.1

WARNING Electricity is dangerous.

 Before commencing work, ensure that you read and understand these instructions and isolate 

the relevant circuit. 

This product should only be installed by a qualified electrician or heating engineer 

and should be installed 

in accordance to BS 7671 (IEE Wiring Regulations), or to another equivalent standard.

CAUTION: High Voltage Wires

The NS1003 series is designed to control a typical domestic central heating system. The Relay module 
can switch three independent channels. This would usually be the 2 Central Heating Zones and the Hot 
Water or 3 Central Heating Zones. 

The central heating channel is switched on and off in response to commands from the supplied Wireless 
Thermostat.

The Hot Water channel is switched on and off at the programmed time intervals that the user sets.

Whats in the box

Introduction

2(or 3) x Assembled Room Thermostat consisting of
 

1 x Room Thermostat

 

1 x Wall Mount

1 x Assembled Relay Module consisting of
 

1 x Control Board

 

1 x Wall Mount

 

1 X Front Cover

1 x Gateway
1 x Network Cable
1 x Power Supply
2(or 3) x Thermostat screw pack
1 x Relay Module Screw Pack
4(or 6) x Batteries

Gateway

Room Thermostat

Relay Module

Relay Module 

Screw Pack

Thermostat 

Screw Pack

Batteries Network Cable

Power Supply

Summary of Contents for NS1003











Reviews: