background image

Part No 1171724

1

Invacare® Matrx® PB Elite

Invacare®

 

Matrx® 

PB Elite

Model Numbers PBE, PBE-FB and EDB

1 General

1.1

Symbols

Signal words are used in this manual and apply to hazards or unsafe practices which could result in 
personal injury or property damage. See the information below for definitions of the signal words.

1.2

Overview

Important Information

The best way to avoid problems related to pressure sores is to understand their causes and your role in 

a skin management program.
Your therapist and physician should be consulted if you have questions regarding individual limitations 

and needs.
All cushions should be selected carefully. Working with your therapist and physician is the best way to 

assure that a cushion choice matches your individual needs.
As the needs of the individual become more complex, cushion evaluation becomes more important.

Invacare Matrx Elite

The Invacare Matrx Elite back is contoured to provide precise orientation within the wheelchair for 

optimal postural support.  The foam is oversized to provide extra comfort and protection. 
The Invacare Matrx Elite back includes a movable foam lumbar pad that can be installed/inserted behind 

the existing foam cushion to provide additional positioning capability. Refer to Lumbar Support (Optional) 

on page 10 for instructions on how to insert and adjust your lumbar support.

Outer Cover

The outer cover is made of a mesh material that is moisture resistant and breathable. Regular cleaning 

and inspection of the outer cover is recommended. Refer to Care and Maintenance on page 10.

WARNING

Warning indicates a potentially hazardous situation which, if not avoided, could result in death or 

serious injury.

CAUTION

Caution indicates a potentially hazardous situation which, if not avoided, may result in property 

damage or minor injury or both.

Gives useful tips, recommendations and information for efficient, trouble-free use.

User Manual

DEALER:

 This manual MUST be given to the user of the product.

USER:

 BEFORE using this product, read this manual and save for 

future reference.

Summary of Contents for EDB













Reviews: