background image

©2010 IWAKI CO., LTD.

Thank you for choosing our product.

Please read through this instruction manual before use.

This instruction manual describes important precautions and instruc-
tions for the product. Always keep it on hand for quick reference.

Instruction manual

EHN-YN (multi-tube connection)

Iwaki
Electromagnetic Metering Pump

Sa

fet

y i

nst

ru

cti

on

s

O

ve

rv

iew

In

stal

lat

ion

O

pe

ra

tion

M

aint

ena
nc

e

Sp

eci

fic

ation
s

T944 '16/04

http://www.iwakipumps.jp

 IWAKI CO.,LTD.  6-6 Kanda-Sudacho 2-chome Chiyoda-ku Tokyo 101-8558 Japan

TEL: +81 3 3254 2935   FAX: +81 3 3252 8892

European office

 / IWAKI Europe GmbH

 

TEL: +49 2154 9254 0   FAX: +49 2154 9254 48

Norway

 / IWAKI Norge AS

 

TEL: +47 23 38 49 00   FAX: +47 23 38 49 01

Australia

 / IWAKI Pumps Australia Pty Ltd.

 

TEL: +61 2 9899 2411   FAX: +61 2 9899 2421

Germany

 / IWAKI Europe GmbH

 

TEL: +49 2154 9254 50   FAX: +49 2154 9254 55

Sweden

 / IWAKI Sverige AB

 

TEL: +46 8 511 72900   FAX: +46 8 511 72922

China

 (Hong Kong) / IWAKI Pumps Co., Ltd.

 

TEL: +852 2607 1168   FAX: +852 2607 1000

Holland

 / IWAKI Europe GmbH (Netherlands Branch)

 

TEL: +31 74 2420011   FAX: +49 2154 9254 48

U.K.

 / IWAKI Pumps (U.K.) LTD.

 

TEL: +44 1743 231363   FAX: +44 1743 366507

China

 (Guangzhou) / GFTZ IWAKI Engineering & Trading Co., Ltd.

 

TEL: +86 20 84350603   FAX: +86 20 84359181

Italy

 / IWAKI Europe GmbH (Italy Branch)

 

TEL: +39 0444 371115   FAX: +39 0444 335350

U.S.A.

 / IWAKI America Inc.

 

TEL: +1 508 429 1440   FAX: +1 508 429 1386

China

 / IWAKI Pumps (Shanghai) Co., Ltd.

 

TEL: +86 21 6272 7502   FAX: +86 21 6272 6929

Spain

 / IWAKI Europe GmbH (Spain Branch)

 

TEL: +34 93 37 70 198   FAX: +34 93 47 40 991

Argentina

 / IWAKI America Inc. (Argentina Branch)

 

TEL: +54 11 4745 4116

Korea

 / IWAKI Korea Co., Ltd.

 

TEL: +82 2 2630 4800   FAX: +82 2 2630 4801

Belgium

 / IWAKI Belgium N.V.

 

TEL: +32 13 670200   FAX: FAX: +32 13 672030

Singapore

 / IWAKI Singapore Pte Ltd.

 

TEL: +65 6316 2028   FAX: +65 6316 3221

Taiwan

 / IWAKI Pumps Taiwan Co., Ltd.

 

TEL: +886 2 8227 6900   FAX: +886 2 8227 6818

Denmark

 / IWAKI Nordic A/S

 

TEL: +45 48 242345   FAX: +45 48 242346

Indonesia

 / IWAKI Singapore (Indonesia Branch)

 

TEL: +62 21 6906606   FAX: +62 21 6906612

Thailand

 / IWAKI (Thailand) Co., Ltd.

 

TEL: +66 2 322 2471   FAX: +66 2 322 2477

Finland

 / IWAKI Suomi Oy

 

TEL: +358 9 2745810   FAX: +358 9 2742715

Malaysia

 / IWAKIm SDN. BHD.

 

TEL: +60 3 7803 8807   FAX: +60 3 7803 4800

Vietnam

 / IWAKI Pumps Vietnam Co., Ltd.

 

TEL: +84 613 933456   FAX: +84 613 933399

France

 / IWAKI France S.A.

 

TEL: +33 1 69 63 33 70   FAX: +33 1 64 49 92 73

Summary of Contents for EHN-B11-NAE





































































Reviews: