The JA-114E Bus access module with LCD, keypad and RFID
The JA-114E Bus access module with LCD, keypad and RFID
MLU51105
The keypad is a component of the
JABLOTRON
JA-100
system
.
Its
modular architecture enables users to create a combination whose size
of installation perfectly meets their needs. The device should be
installed by a trained technician with a valid certificate issued by
authorized distributor.
The keypad comprises a display, an RFID card / chip reader and the
first control segment (1). JA-192E segments can be used to extend the
JA-114E unit by the required number of segments (the max. allowed
amount is 20 on one unit). The tilting keypad cover (6) can be removed
if the user prefers permanent access.
Figure: 1
– control segment; 2 – segment buttons; 3 – backlit activation
button; 4
– LCD; 5 – keypad module with RFID; 6 – tabs for opening;
7 - cover screws
Figure: 8
– control segment connector; 9 – production code;
10
– bus terminals; 11 – tamper contact
Installation
1.
Gradually press the four tabs (6) on the sides and release the
keypad from the plastic base.
2.
When installing more control segments, first remove the socket
cover on the 1
st
segment.
3. Remove the plastic windows from the segments (by levering on
both sides of the segments near the buttons).
4.
Always connect the segment wires to the connector of the previous
segment and click them into each other (we recommend coiling the
wires by turning the segment by 360°
– this will prevent any
possible damage to the wires between the plastic parts). Use this
method to install all the required control segments. Finally, push the
socket cover in.
5.
Push the
cable through the plastic base and attach it
to the
selected place together with the segments
using screws.
If
multiple control segments are required, attach them onto the wall
using screws as well (use the number of screws required).
6.
Connect the bus cable to the bus terminals (10).
When connecting the module to the bus,
always switch the power off.
7. Connect the segment wires to the internal connector of the keypad
(8).
8. Insert the keypad into the base.
9. Proceed according to the control panel installation manual. Basic
procedure:
a.
When the device is switched on, the yellow LED starts flashing
repeatedly to indicate that the keypad has not been enrolled
into the system.
b. Go to the
F-Link
program, select the required position in the
Devices
window and launch the enrollment mode by clicking
on the
Enroll
option.
c.
Press the backlit activation button (3) above the screen
– the
keypad is thus enrolled and the yellow LED indicator goes off.
10.
When you have completed the installation, insert descriptive labels
onto the segment plastic windows and close them. Label printing is
a part of the F-Link program (
Devices
window, at the keypad
position
–
Internal settings
).
Note: To comply with the EN 50131-3 norm it is necessary to fix the
cover tab by the screws from the accessories. In picture no 1 the
cover tabs are fixed by the arrows.
Figure: Inserting a label into a control segment
Setting the properties
Go to the
Devices
window in the F-Link program. When you are at
the keypad position, use the
Internal settings
option. The particular
unit is displayed and it is possible to set its properties. It is possible to
set the required functions for individual segments (control of sections,
section status signalling, alarm triggering, PG output control, PG output
status signalling, etc.). More details are available in the F-Link program.
A common segment (up to 2 of them allowed on one keyboard) simulates
the simultaneous pressing of several segments which are placed on this
keyboard and which control sections. The selection of sections which are
assigned to the common segment is performed by F-Link SW, the
Devices
window. At the keyboard position select
Internal settings / and Common
segment 1 (2)
and mark the segments which will be operated en bloc. The
selected sections will be set / unset after pressing a button on the common
segment. If the states of the segments which are operated by the common
segment are mixed, then only the segments that need changing will be set /
unset. If partial setting is enabled for some segments, then the common
segment respects this: 1 st. press = partially setting, 2
nd
press = full setting. It
is not suitable to combine a common segment with a common section
The indication of the common segment is: all segments set = green, some
set (partially set) = yellow, all sections fully set = red.
Unit modifications
If you need to change the unit’s individual segments, it is possible to
separate them by levering the corresponding separating gaps from one
side (sideways from the buttons).
