WARNING! This device is not intended for use
with emergency exit fixtures or emergency
exit lights.
WARNING! Permanent damage to the low
voltage 14VAC lamp will occur if installed on
a 120VAC circuit.
PureWhite Replacement LED In-Ground Pool lamps are available in 14VAC
(low voltage) and 120VAC models as indicated on the product packaging.
Each lamp has a screw-in Edison base.
WARNING! Remove warning label from
PureWhite lens before installation.
The warning label is placed on top of a special optical diffuser
designed to maximize the light projection of the PureWhite lamp. When
you remove the label, a protective film will come off with it. Once the
warning label and protective film have been removed, do not allow the
diffuser decal underneath to be scratched.
ATTENTION 14V PUREWHITE OWNERS!
A socket voltage range of 13.5 – 15.0 will achieve optimal brightness.
To verify the voltage, at the lamp socket, measure the open circuit
voltage (no lamp in the socket). Set the transformer tap to 14.0VAC.
DANGER!
Risk of electrical shock or electrocution
Always disconnect power to the pool light at the circuit breaker
panel before attempting to service the lamp. Failure to do so could result
in serious injury or death due to electrical shock. Refer to the original
manufacturer’s pool light installation manual before proceeding. As with
any electrical device, installation and service should always be performed
by a qualified individual.
This device is not intended for use in anything
other than in-ground pools.
Rated Lamp Life
The illumination generated by the PureWhite Replacement LED In-Ground
Pool lamp is based on Light Emitting Diode (LED) technology. The average
expected lamp life is rated up to 50,000 elapsed time hours under normal
operating conditions. [Temperature: 33°F to 95°F (1°C to 35°C), Humidity:
0-95% non-condensing].
Safety Precautions
• Do not open, service or tamper with any internal component of the
PureWhite Replacement LED In-Ground Pool lamp. Doing so will
void the warranty. Follow each instruction in this owner’s manual
and pay careful attention to all warnings.
• Do not directly expose or immerse the PureWhite Replacement LED
In-Ground Pool lamp in water without containing it in a proper,
watertight, NRTL (nationally recognized testing laboratory) pool
light housing and niche assembly.
• Keep the pool light housing dry.
• Handle the PureWhite Replacement LED In-Ground Pool lamp with
care. Be careful not to drop the unit.
IMPORTANT NOTE:
PureWhite lamps are recommended for installation by a qualified pool
professional.
J&J Electronics
•
35 Hammond, Irvine, CA 92618 USA
•
800.735.4553
•
949.455.4460
•
www.jandjpoolspa.com
PAGE 1
PureWhite
™
Pool Lamp Installation and Operation Guide
PUREWHITE REPLACEMENT LED IN-GROUND POOL LAMPS
Model #s: LPL-P1-WHT-12, LPL-P1-WHT-120
PureWhite Replacement LED In-Ground Pool lamps offer superior, bright white illumination for your pool. This owner’s manual contains important
information on installing and using your new PureWhite Replacement LED In-Ground Pool lamp. Please read it carefully and keep it in a safe place for
future reference.
Installation
The installation steps in this owner’s manual
are intended as guidelines. For specific
instructions on how to replace a pool lamp,
please refer to the original manufacturer’s
pool light installation manual before
proceeding.
Light housing compatibility
LPL-P1-WHT-12 and LPL-P1-WHT-120
PureWhite Replacement LED In-Ground
Pool lamps must be installed in a
compatible NRTL pool light housing.
Compatible NRTL light housings include:
Hayward
®
Astrolite
™
SP058 Series
Pentair
®
Amerlite 784 Series
Jacuzzi
®
Full Moon
™
WARNING!
Read this before attempting installation
Your PureWhite lamp is not an ordinary light bulb. It is a valuable
electronic device that is not designed to come in direct contact with water.
An improper installation that results in water leakage into the pool light
housing can permanently damage the PureWhite lamp.
Please read these
installation steps and the original manufacturer’s pool light installation
manual carefully before proceeding.
STEP 1
Remove light housing from niche
Make sure power to the pool light is turned off at the circuit breaker. Care-
fully remove the existing light housing from the niche assembly and place
it on the pool deck. There should be enough power cord to do this easily.
If there is not enough power cord to allow the light housing to reach the
pool deck surface, call your local pool service company.
WARNING! Verify that your PureWhite lamp
voltage rating (120VAC or 14VAC) matches
your electrical system’s voltage requirements
before proceeding with installation.
