JANE V
- Radiocomando che copia in autoapprendimento codici fissi e frequenze diverse per ogni singolo
canale.
PROCEDURA DI DUPLICAZIONE
- La procedura di duplicazione avviene per ogni singolo tasto.
1. Premere i tasti 1 e 2 contemporaneamente e rilasciare quando il
LED
inizia a lampeggiare.
Il tempo massimo per passare alla fase successiva è di 20 secondi, poi il
LED
terminerà di lampeggiare
spegnendosi e uscendo dalla programmazione.
2. Posizionare il
JANE V
e il radiocomando funzionante come
figura 1
.
3. Premere, senza rilasciare, prima il tasto del radiocomando funzionante e poi il tasto del
JANE V
che si
intende duplicare.
Il
LED
inizia a lampeggiare più velocemente procedendo alla ricerca di tutte le frequenze per individuare
quella giusta e una volta trovata, acquisirà anche il codice. Questa operazione dura dai 6 ai 12 secondi circa.
Trovata la frequenza e il codice del radiocomando funzionante, il
LED
confermerà la buona riuscita
diventando fisso e successivamente spegnendosi.
4. Rilasciare il tasto del
JANE V
e quello del radiocomando funzionante.
Per programmare un nuovo tasto ripetere tutta la procedura.
Se durante la ricerca della frequenza e del codice, il
LED
si spegne, ripetere tutta la procedura.
Se dopo vari tentativi non apprende, ripetere la procedura premendo prima il tasto del
JANE V
nel punto 3
della programmazione, o sostituire la batteria del radiocomando funzionante.
Nel caso in cui la trasmissione del radiocomando funzionante sia troppo breve e il
JANE V
non riuscisse
a trovare la frequenza, tornare al punto 3 e premere per circa 3 secondi ripetutamente il tasto del
radiocomando funzionante in modo da aumentarne il tempo.
Nel caso in cui la programmazione sia andata a buon fine, ma non funzionasse,ripetere la
PROCEDURA DI
DUPLICAZIONE
modificando la posizione della
figura 1
ad una distanza di circa 1/2 cm uno dall’altro.
JANE V
- Remote control that copies and saves different fixed codes and frequencies for each individual
channel.
DUPLICATION PROCEDURE
- Duplicate codes for each individual button.
1. Press buttons 1 and 2 at the same time and release when the
LED
starts to flash.
The maximum time before the next stage will be 20 seconds, then the
LED
will stop flashing by switching
off and exiting the programming phase.
2. Position the
JANE V
and the original remote as in
figure 1
.
3. Press and hold first the button of the original remote and then the button on the
JANE V
you wish to
programme.
The
LED
will start flashing more quickly as it searches all the frequencies for the right one. Having found it,
it will also acquire the code. This operation lasts around 6 to 12 seconds.
Having found the frequency and the code of the original remote, the
LED
will confirm completion by
stopping flashing and then switching off.
4. Release the buttons on the
JANE V
and on the original remote.
To programme a new button repeat the whole procedure.
If the
LED
switches off during the search for the frequency and the code, repeat the entire procedure.
If it does not save the code after repeated attempts, repeat the procedure by pressing first the button on
the
JANE V
at point 3 of the programming, or replace the battery of the original remote.
If the transmission of the original remote is too short and the
JANE V
cannot find the frequency, return to
point 3 and press the button on the original remote for around 3 seconds repeatedly to increase the time.
When the programming has completed successfully, but it does not work, repeat the
DUPLICATION
PROCEDURE
by changing the position of the devices in
figure 1
to a distance of around 1/2 cm from
one another.
Caratteristiche Tecniche
Frequenza
433 - 868 MHz
Alimentazione
batteria litio 3v (CR2032)
Codifica
codice FISSO
Numero canali
2-4
Consumo di trasmissione
23 mA
Tipo oscillatore
SAW
FIGURA 1
FIGURE 1
Come sostituire la batteria
Technical Information
Frequency
433 - 868 MHz
Supply
lithium battery 3v (CR2032)
Encryption
FIXED code
Number of channels
2-4
Transmission consumption
14 mA
Oscillator type
SAW
How to replace the battery
LED VERDE
GREEN LED
Garanzia: 24 mesi - Fabbricazione e tecnologia: 100% made in Italy - Prodotto brevettato.
Dichiarazione di conformità
Il sottoscritto Luigino Pellattiero, in qualità di legale rappresentante della ditta ITALFILE srl, dichiara che il
radiocomando JVxxx-2/JVxxx-4, anno di fabbricazione 2012 è stato costruito rispettando le seguenti norme:
Direttiva 2004/108/CE - nota come Direttiva Compatibilità Elettromagnetica.
Direttiva 2002/95/CE - nota come direttiva RoHS - Ed è quindi conforme alle normative vigenti.
Italfile srl - L’amministratore Luigino Pellattiero
Warranty: 24 months - Manufacturing and technology 100% made in Italy - Patented product
Compliance statement
The undersigned Luigino Pellattiero, legal representative of ITALFILE srl, declares that the remote control JVxxx-2/
JVxxx-4, manufactured in 2012 was assembled in compliance with the following standards:
Directive 2004/108/CE - known as the Electromagnetic Compatibility Directive
Directive 2002/95/CE - known as the RoHS Directive - And therefore complies with current standards.
Italfile srl - Administrator Luigino Pellattiero
Pr
odotto br
evettato
Via Gualda, 11 - 36075 Montecchio Maggior
e (VI) – IT
www
.telecomandojane.com
ITA
ENG
ESP
FRA
Grazie per
aver scelto
JANE V
Patented pr
oduct
Via Gualda, 11 - 36075 Montecchio Maggior
e (VI) – IT
www
.telecomandojane.com
ITA
ENG
ESP
FRA
Thank you
for choosing
JANE V
WORKING
JANE