background image

I N S T A L L A T I O N   G U I D E 

for the 

SMS-P-987C-BASE

SMS-P-987C-PREM 

SKU# 94556/94569

2006 & Up Porsche Cayman 987C   

Thank you for choosing a JL Audio StealthMod® System for your automotive sound system.  

With proper installation, your new vehicle-specific audio system  

will deliver years of listening pleasure.

We strongly recommend that you have your new StealthMod® System installed by your authorized  

JL Audio dealer. The installation professionals employed by your dealer have the necessary tools 

and experience to disassemble and reassemble your vehicle properly.  If you prefer to perform your 

own installation, please read this installation guide completely before beginning the process.

  

If you choose to perform the installation yourself, it is absolutely vital that 

the Stealthbox

®

 be properly mounted to the vehicle according to these 

instructions.  Failure to mount the enclosure properly presents two problems:  
1) The sub-bass performance will suffer due to the movement of the enclosure 

caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision 

or sudden deceleration.

Continued on Next Page 

SMS-P-987C  INSTR_SKU# 011358

INSTALLATION  

D I F F I C U L T Y :

4

5

OUT   

OF

ESTIMATED TIME:

         4 HOURS

S T E A L T H B O X ®   S P E C I F I C A T I O N S

 

Enclosure Type:

  Sealed

Driver Type:

  13TW5v2-2

Nominal Impedance:

  2 ohms

Continuous Power Handling:

  600 watts (RMS method)

I N C L U D E D   E Q U I P M E N T

(1) HD900/5 Amplifier
(1) Pair C5-650x
(1) XD-MFB-MAXI Fuse Holder
(1) XD-MAXI-60 Fuse
(1) Pair XD-CLRAIC2-SW Speaker to RCA Adaptor
(2) XD-CLRAICY-1F2M Y-adaptor
(1) XD-CLRAIC2-12 RCA Cable

Premium System Only:

(1) CL-SSI

I N C L U D E D   H A R D W A R E

 

(1) Amplifier Cover Panel                                 (1) Terminated 60 Amp Power Wire
(2) Speaker Adaptor                                         (1) Terminated 60 Amp Ground Wire
(2) Crossover Adaptor                                      (1) 16 Gauge Speaker Cable
(4) Foam Tape Strip                                          (1) 12 Gauge Speaker Cable
(4) #8 x 5/8” Pan Head Screw                          (1) 16 Gauge Remote Wire
(4) #8 x 1/2” Pan Head Screw                          (4) Snap Grommet
(4) 8 - 32 x 5/8” Screw                                      (16) #8 x 3/4” Pan Head Screw
(4) #8 Lock Washer                                           (1) 1/2” Split Loom
(1) Fuse Tap                                                       (1) 1” Split Loom
(1) Fuse Holder
(1) 3 amp fuse
(1) 1 amp fuse

Premium System Only:

(4) 8 - 32 x 3/8” Screw
(4) #8 Flat Washer
(4) #8 Lock Washer

StealthMod

®

Summary of Contents for 94556











Reviews: