background image

 

 

1

 

John Lewis

         

Morgan Office Chair 

Stock number: 816/31276 & 816/31279 

 

 

 

 

 
Thank you for purchasing this product. Please read the instructions carefully before use to ensure safe 
and satisfactory operation of this product.

 

 
 

 
 
 
 
 
 

 

 
 
 
 
 
 
 

 
 

 

Pre-assembly preparation 

 

Please ensure instructions are read in full before attempting to assemble this product. 

 

 

Necessary Tools 

                                                             

 

 

Please check the pack contents before attempting to assemble this product. A full checklist of parts is 
given in this leaflet. If any parts are missing, broken, damaged, or worn, stop using this product until 
repairs are made and factory replacement parts are installed. You may obtain replacement parts by 
calling 

0-800-051-6775 (UK)

.  

Please note that a receipt is required for all warranty replacements. Service hours are: UK Standard 
Time: 

2:00 pm-1:00 am Monday – Friday

 
This product is 

HEAVY

, it should be assembled as near as possible to the point of use. 

TAKE CARE 

WHEN LIFTING

 to avoid personal injury and (or) damage to the product.  

 
This product takes approximately

 

20 MINUTES

 to assemble with 

2 PEOPLE

 
The fittings pack contains 

SMALL ITEMS

 which should be 

KEPT AWAY FROM YOUNG 

CHILDREN

.   

 
Read this leaflet in full before commencing assembly. 

 

Summary of Contents for Morgan Office Chair










Reviews: