background image

-1-

Instruction Manual

AD-7830 Servo Amplifier

Table of Contents

General Information ................................................. 2

Introduction ....................................................... 2
Receiving/Inspection .......................................... 2
Storage ............................................................... 2
Equipment Return .............................................. 2
Abbreviations Used in This Manual .................... 2

General Description ................................................. 3

Actuator Compatability ....................................... 3
Basic Models ...................................................... 3
Specifications ..................................................... 3

Installation Wiring .................................................... 3
Set-up and Calibration .......................................... 4-5
Component Location ............................................... 6
Troubleshooting Guide ............................................. 7
Typical Wiring Diagrams .......................................... 8
Major Dimensions ............................................... 9-10

IM-0606

Due to wide variations in the terminal numbering

of actuator products, actual wiring of this device

should follow the print supplied with the unit.

Summary of Contents for AD-7830











Reviews: