background image

SERVICE MANUAL

COPYRIGHT © 2008 Victor Company of Japan, Limited

No.YF266<Rev.001>

2008/11

HARD DISK CAMCORDER

YF266<Rev.001>

2008

11

SERVICE MANUAL

EVERIO G

GZ-MG330AUA, GZ-MG330RUA

COPYRIGHT © 2008 Victor Company of Japan, Limited

Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)

This service manual (No.YF266<Rev.001>) describes only the items which differ from those of already issued service manual (

No.YF226

<Rev.002>)

For details other than those described in this manual, please refer to the service manuals which were already issued.

TABLE OF CONTENTS

1

PRECAUTIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-3

2

SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-5

3

DISASSEMBLY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-6

4

ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-17

5

TROUBLE SHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-20

GZ-MG330AUAM, GZ-MG330RUAM [M8E303]

Summary of Contents for GZ-MG330AUA






















Reviews: