background image

Page 1

November 17, 2000 12:40 pm

VIDEO CASSETTE RECORDER

HR-VP793U

INSTRUCTIONS

LPT0502-001

B

 Printed in Malaysia

COPYRIGHT © 2000 VICTOR COMPANY OF JAPAN, LTD.

1100 IYV

f

ID

f

PJ

Dear Customer,

Thank you for purchasing the JVC VHS video cassette recorder. 
Before use, please read the safety information and precautions to 
ensure safe use of your new VCR.

CAUTIONS

Failure to heed the following precautions may result in damage 
to the VCR, Remote or video cassette.

1. DO NOT place the VCR . . .

...in an environment prone to extreme temperatures or 
humidity.
...in direct sunlight.
...in a dusty environment.
...in an environment where strong magnetic fields are 
generated.
...on a surface that is unstable or subject to vibration.

2. DO NOT block the VCR’s ventilation openings.
3. DO NOT place heavy objects on the VCR or on the Remote.
4. DO NOT place anything which might spill on the top of the 

VCR or on the Remote.

5. AVOID violent shocks to the VCR during transport.

VCR Plus+, C

3

 and PlusCode are registered trademarks of Gemstar 

Development Corporation.
The VCR Plus+ system is manufactured under license from 
Gemstar Development Corporation.

Cassettes marked “VHS” (or “S-VHS”) can be used with this 
video cassette recorder. However, S-VHS recording is not 
possible with this model.

This model is equipped with SQPB (S-VHS QUASI PLAYBACK) 
that makes it possible to play back S-VHS recordings with 
regular VHS resolution.

HQ VHS is compatible with existing VHS equipment.

As an E

NERGY

 S

TAR

®

 Partner, JVC has determined that this 

product or product model meets the E

NERGY

 S

TAR

®

 guidelines for 

energy efficiency.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE 
THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

This video cassette recorder should be used with AC 120V

d

60Hz only.
To prevent electric shocks and fire hazards, DO NOT use any 
other power source.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF 
PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA 
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE 
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU 
FOND.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s 
attention to Article 820-40 of the NEC that provides guidelines 
for proper grounding and, in particular, specifies that the cable 
ground shall be connected to the grounding system of the 
building, as close to the point of cable entry as practical.

The lightning flash with arrowhead symbol, within 
an equilateral triangle, is intended to alert the user 
to the presence of uninsulated “dangerous voltage” 
within the product’s enclosure that may be of 
sufficient magnitude to constitute a risk of electric 
shock to persons.

The exclamation point within an equilateral triangle 
is intended to alert the user to the presence of 
important operating and maintenance (servicing) 
instructions in the literature accompanying the 
appliance.

CAUTION:

Changes or modifications not approved by JVC could void 
user’s authority to operate the equipment.

Declaration of Conformity

Model Number:

HR-VP793U

Trade Name:

JVC

Responsible Party:

JVC Americas Corp.

Address:

1700 Valley Road Wayne, N.J. 07470

Telephone Number: 973-315-5000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this 
device must accept any interference received, including 
interference that may cause undesired operation.

For Customer Use:

Enter below the Model No. and Serial No. which are located 
on the rear of cabinet. Retain this information for future 
reference.
Model No.

Serial No.

HR-VP793U-EN.fm  Page 1  Friday, November 17, 2000  12:40 PM

Summary of Contents for HR-VP793U

















Reviews: