5
Turning the TV On for the First Time
Do not connect the TV to the mains supply until you have completed all the connections.
Install the batteries correctly by following the polarity (+ and -) indications
in the battery compartment.
Well done,
your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these features, please
take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please click on the link for Support Centre:
Norway: www.elkjop.no/service Sweden:
www.elgiganten.se/service
Denmark: www.elgiganten.dk/service Finland:
www.gigantti.fi/huolto
1. The first time you turn the TV on, it will go
straight into First Time Installation menu.
Press the OK button to start First Time
Installation menu.
2. Press the buttons to select your
desired language to be displayed on the
menu. The default on-screen menu language
is set as English. Press the OK button to
confirm.
4. Press the buttons to select DVB-T /
DVB-C and then press the OK button to
confirm.
5. Channel tuning will commence. This operation
may take up to 6 minutes. The display will
show the progress of the tuning and the
number of channels found.
First Time Installation
Please ensure aerial is plugged in!
Then press OK button.
OK
English
Svenska
Dansk
ýesky
Slovak
Norsk
Suomi
Please select an OSD Language
DVB-C
DVB Select type
DVB-T
OK
Home Mode
Shop Mode
Mode Select
Tune Type
DTV
Germany
Greece
Hungary
Italy
Ireland
Luxembourg
Netherlands
Norway
Poland
MENU
DVB-C Scan Menu
Scan type
Full
610000
Auto
Auto
Frequency
Network ID
Symbol(ks/s)
OK
MENU
Channel Tuning
DTV
: 3 Channel(s)
Radio : 0 Channel(s)
Data : 0 Channel(s)
36%
UHF CH
Press [MENU] to skip.
(DTV)
4b. If you select DVB-C, the next step is to
configure the DVB-C system (Scan type /
Frequency / Network ID / Symbol(ks/s)).
Press the OK button to go to the tune type
and add country select menu. This step is
the same as the DVB-T's select the tune type
(DTV / ATV) process. Press the
buttons to select the desired country and
then press the OK button to start tuning.
4a. If you select DVB-T, press the buttons
to select DTV / ATV / ATV + DTV. Press the
button and then press the
buttons to select the desired country and.
Press the OK button to start tuning.
During tuning your TV may have received signals
from more than one transmitter. If this has
occurred the Target Region Setting screen will be
displayed. This will enable you to select the
correct regional transmission for the local news
service that you require.
Press the buttons to adjust each option's
setting and then press the OK button to confirm.
Target Region Setting
Country Code
GBR
Primary Region
England
Secondary Region
Tertiary Region
London
This will be shown as GBR for the UK.
Target Region Setting
1
2
3
4
1
This will show the regional country (e.g. England,
Wales, Scotland, NI).
2
This will allow you to set the region for your local
news service on BBC and ITV (e.g. London, Beds and
Cambs etc).
3
You may receive signals from more than one
transmitter within the Secondary Region, (e.g Beds
and Cambs may have Luton or Sandy Heath).
4
3. Press the buttons to select your desired
mode and then press the OK button. Press
the button to select Yes to confirm or the
button to select No to cancel and return to
the Mode Select menu.
(QSG-LT-40E71-131126V1-1)
1. Lay the TV down on a flat surface with the back side facing up, and ideally at the edge of a table so that the base of the TV slightly overhangs on it. Please
make sure a soft cushioned material (such as a pillow or thick piece of foam) is placed beneath the screen.
2. To install the TV stand, first attach the stand support to the TV by using 2 screw A and 2 screw B. Align with the screw hole then use screws to fix the stand
support to the TV.
3. To install the base stand, align the screw holes, then secure with a screw driver (not included) using the 4 screw C provided.
Quick Start Guide
40” FHD LED TV
LT-40E71
Thank you
for purchasing your new JVC TV.
Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 20 mins for initial
setup.
Please follow this guide for a successful first time installation.
1
Unpacking
2
Operating Your Remote Control
4
Connecting the Aerial and the Mains Socket
3
Installing the Base Stand
1. Press and lift the back
cover to open the battery
compartment of the
remote control.
Remove all packaging from the unit. Retain the packaging.
If you dispose of it please do so according to any local regulations.
2. Insert two AAA size
batteries. Close the
battery compartment
cover.
GB
The latest eco-friendly power-saving technology will switch off the TV if
device is left on and idle for 4 hours. Please refer to “Auto Standby” under
the “Time Settings” section of the instruction manual for more detail.
1. Connect one end of the RF coaxial cable to the aerial socket on
the wall and the other end of the cable to the RF (75Ω) socket
at the rear right side of your TV.
2. Connect the mains cable to the mains socket after you have
completed all the connections.
3. Switch on the POWER ON/OFF switch which is located at the
front right side under the frame. At this stage, the TV switches
to standby mode. The red LED indicator will illuminate on the
front panel of the TV.
4. In standby mode, press the button on the right side panel
of the TV or on the remote control to turn the TV on. The red
LED indicator will turn blue.
1
2
3
USB
5V
500mA
HDMI2
HDMI1(ARC)
PC IN
RF
COMMON INTERFACE (CI)
HEADPHONE
PC AUDIO
To mains socket
RF Coxial Cable
(not included)
OR
TV
TV Stand Support
TV Base
Remote Control /
AAA Batteries x 2
Screw A x 2
Quick Start Guide
Instruction Manual
Screw B x 2
Screw C x 4
screw in
screw in
Screw A
A
B B
Screw C x 4
TV Front
Base Stand
Front
LT-40E71_QSG_131126_Annie.pdf 1 26/11/13 4:14 PM
