QUICK REFERENCE GUIDE
X-09
Note:
If at any time the dial remains stationary
for more than 40 seconds, the lock will reset
(LCD will go blank) requiring the operator to redial
the entire combination or restart the operation.
OPEN THE LOCK
(Factory Combination = 50-25-50)
Single Combination Mode:
1.
Dial
left
until lock is “powered”.
2.
Continue dialing
left
to first number of
combination.
Stop
3.
Dial
right
to second number of combination.
Stop
4.
Dial
left
to third number of combination. Stop.
5.
Dial
right
. After
OP
with a right arrow is
displayed, continue dialing right to retract
bolt.
Dual Combination Mode
:
First Operator
1.
Dial the first combination as in Single Mode.
2.
Dial
right
until
C2
is displayed.
Second Operator
3.
Within 40 seconds dial
left
to first number of
the second combination.
Stop
4.
Dial
right
to second number of combination.
Stop
5.
Dial
left
to third number of combination. Stop.
6.
Dial
right
. After
OP
with a right arrow is
displayed, continue dialing right to retract
bolt.
Supervisory/Subordinate Mode
:
•
To Unlock (UL)
To enable lock access for the Subordinate
combination, dial the Supervisor combination as if
dialing the combination to open the lock. Then dial
right
and
UL
will appear on the display. Once the
lock is in an Unlocked status, the Subordinate
combination can be used to open the lock at any
time.
•
To Lock Up (LU)
To disable lock access for the Subordinate
combination, reenter the Supervisor combination.
Then dial
right
and
LU
will display and the
Subordinate combination will no longer open the
lock.
SET OPERATING MODE and CHANGE
COMBINATION(s):
1.
Open the lock and retract the bolt to open
container if not already open.
Note:
If using the serial number method,
simply dial an incorrect combination to get a
lightning bolt.
2.
Insert Change Key into back of lock.
3.
Release container locking bolts if necessary.
4.
Dial
left
until lock is “powered”. The Change
Key symbol will be displayed.
5.
Dial
left-right-left
to dial the current
combination(s).
Note:
If using the serial number method, dial
the serial number at this time.
6.
Dial
right
until
SL
is displayed.
7.
Dial
left
to select the mode of operation:
1
-Single Mode,
2
-Dual Mode, or
3
-Super/Sub Mode
Once the mode is selected, pause briefly.
If selection 1, Single Combination Mode:
8.
Dial
right
until
EC
appears.
9.
Dial
left-right-left
to dial the
new combina-
tion
as if dialing the combination to open the
lock.
10. Dial
right
briskly. The new combination will
be displayed two times, two digits at a time,
followed by
PO
.
11. Pull Out change key.
CC
will appear.
12. Dial
left-right-left
to dial
new combination
again for confirmation. Once
OP
with a right
arrow is displayed, continue dialing right to
retract the bolt.
The new combination is now set.
If selection 2 or 3, Dual or Super/Sub Mode:
8.
Dial
right
until
C1
appears.
9.
Dial
left-right-left
to dial the
first new
combination
(Supervisory if Super/Sub
Mode) as if dialing the combination to open
the lock.
10. Dial
right
briskly. The new combination will
be displayed two times, two digits at a time,
followed by
PO
.
11. Dial
right
until
C2
appears.
12. Dial
left-right-left
to dial the
second new
combination
(Subordinate if Super/Sub
Mode) as if dialing the combination to open
the lock.
13. Dial
right
briskly. The new combination will
be displayed two times, two digits at a time,
followed by
PO
.
14. Pull Out change key.
CC
will appear.
15. Dial the
new combinations
once again for
confirmation.
The new combinations are now set.
IF YOU LOCK THE CHANGE KEY IN THE
SAFE
Note:
You cannot use the serial number
in place of the combination for this
procedure. The combination must be
known.
1. Allow lock to power down. (After 40 seconds,
the display will go blank. Wait an additional 2
minutes for full power down.)
2. Dial
right
(CW) until lock is “powered” and the
number of successful openings is flashing.
Caution:
Do not continue to dial right
once you see the flashing numbers on
the display.
3. Now dial the current combination(s) just as
you would to open the lock ; i.e.,
left
(CCW) to
dial the first number,
right
(CW) to dial the
second number,
left
(CCW) to dial the third
number.
4. Dial
right
(CW). After
OP
with a right arrow
(
OP
en right) is displayed, continue dialing to
the right to retract the lock bolt.
You may now restart the procedure to Set
the Operating Mode and Change
Combination(s).
CLOSE / RELOCK CONTAINER
1.
Close container door.
2.
Turn dial
left
a minimum of one complete
revolution to extend the bolt.
3.
Turn dial
right
a minimum of one complete
revolution to ensure it is locked.
Note:
The Dial should turn freely in
either direction without catching or binding
when the bolt is extended and the
container is locked.
CHECK # OF SUCCESSFUL OPENINGS
1. Allow lock to power down. (After 40 seconds,
the display will go blank. Wait an additional 2
minutes for full power down.)
2.
Dial
continuously
to the
right
to display the
total number of successful openings (two
digits at a time).
CHECK # OF UNSUCCESSFUL AT-
TEMPTS
1. Allow lock to power down. (After 40 seconds,
the display will go blank. Wait an additional 2
minutes for full power down.)
2.
Dial
left
until lock is “powered”. If 3 or more
consecutive unsuccessful attempts have
occurred, a lightning bolt along with the two-
digit count will be displayed.
Document Number 522.021 Rev. C 06/03
Kaba Mas Corporation
749 W. Short Street
Lexington, KY 40508 USA
Phone: 859-253-4744
FAX: 859-255-2655
Technical Support: 800-950-4744
www.kaba-mas.com