background image

Overview  . . . . . . . . . . . . . . . . . . . . .1
Precautions  . . . . . . . . . . . . . . . . . .1-2
Assembly Instructions  . . . . . . . . . . . .3
Operating Instructions  . . . . . . . . . . . .4
Using the Accessories  . . . . . . . . . . .5
Working with Detergents  . . . . . . . . . .6
Shut Down and Clean-Up  . . . . . . . . .7
Taking a Break  . . . . . . . . . . . . . . . . .7
Winterizing and Long-Term Storage  .7
Cleaning Tips . . . . . . . . . . . . . . . . .8-9
Optional Cleaning Accessories  . . . . .9
Troubleshooting  . . . . . . . . . . . . .10-11

Model HD 2700 DB

Part No. 1.194-116

Model HD 2700 DH

Part No. 1.194-117

Model HD 3000 DH

Part No. 1.187-115

Model HD 3500 DH

Part No. 1.810-997

Model HD 3500 DB

Part No. 1.810-998

High Pressure Washer Operator Manual

Specifications

Model HD 2700 DH/DB

Operating pressure 2700 PSI
Water volume 

2.8 GPM

Engine 6.5 HP Honda GX 200/

Briggs & Stratton Itek

Model HD 3000 DH

Operating pressure 3000 PSI
Water volume 

3.2 GPM

Engine 9 HP

Honda GX 270

Model HD 3500 DH/DB

Operating pressure 3500 PSI
Water volume 

4.0 GPM

Engine 13 HP Honda GX 390/

Briggs & Stratton Vangard

Manual Part No. 9.139-107

In USA Call:

1-800-537-4129

or visit our website:

www.karcher-usa.com

Summary of Contents for 1.187-115













Reviews: