GAS FILLING
Fill only in a well ventilated area.
The soldering iron runs on butane gas
such as used with ordinary cigarette
lighters. A small amount of liquid gas
should be visible through the gas
inspection window, gas vapour alone
will not generate sufficient pressure.
Do not overfill.
l
Make sure the on/off switch is
in the
“
O
” (off)
position before filling.
l
Hold unit vertically with the
filling valve upwards. Push the gas
re-fill cylinder down onto the filling
valve. The flow of gas from the re-fill
cylinder to the soldering iron
depends on gravity (See fig. 2).
CHANGING THE TIPS
CAUTION:
Allow the tip to cool completely before removing.
Tips are easily removed or installed, by unscrewing the tip retaining
collar and sliding the tip retainer tube off the front end burner.
Replace the tip and reassemble in the reverse order. (See fig. 3)
IGNITION SEQUENCE
The unit is ignited by a piezo-electronic system. The gas “on/off”
switch is marked “I-0”. The ignition switch is marked with a" ".
l
Soldering, hot air, hot knife:
Fit tip of choice and secure with
retention sleeve/collar. Turn temperature regulator button to Max.
setting. Hold away from face and body and push the gas switch
toward the tip, this will release the gas. 'Click back' on piezo
ignition switch and allow to return while still maintaining light
thumb pressure on the switch, this enables the gas flow interrupt
mechanism to extinguish the ignition flame, and allows the
catalyst to assume combustion control. A glowing catalyst, in the
exhaust port, will confirm correct operating mode.
l
Blow torch:
N.B. The flame is difficult to see under certain lighting situations.
Remove only the tip. Turn temperature regulator to mid setting.
Turn gas on as above. ‘Click back’ on piezo ignition switch and
quickly release (the internal spring will provide sufficient speed).
If the speed of return of the piezo switch is slowed slightly by
finger pressure, the gas flow interrupt mechanism may extinguish
the flame. Experience will dictate. Set low to medium settings as
the flame may "blow itself out' at high gas flow.
l
To Switch off:
Push the gas switch away from the tip “
O
” (OFF).
BUTANE SOLDERING TOOL KIT
MODEL BSK075
ORDER CODE KEN-516-9120K
l
Cordless and refillable
l
Uses standard butane
lighter fuel
l
25-75W rating
l
Complete with blow torch,
hot air tool, hot knife and tips
SAFETY GUIDELINES
l
Always use with care. Your soldering iron contains flammable
gas under pressure.
l
Always keep out of the reach of children.
l
Always refill with a high quality butane cigarette lighter fuel.
No other fuel type should be used.
l
Always ensure the flame is extinguished before putting down.
Caution:
Hot gases 580
°
C are emitted from the exhaust port.
l
Always ignite the soldering iron with the tip pointing away from face
and body. Excessive gas flow, flaming or the catalyst pulsing red
to black may occur when igniting or when the regulator is set
too high.
l
Always allow the tip to cool sufficiently before touching.
l
Always ensure that you are in a well ventilated area. This
product, when used for soldering and similar applications,
produces chemicals. Never inhale vapours from fluxes,
plastics, foams etc.
l
Always dispose of in accordance with local regulations.
l
Never leave unattended.
l
Never drop.
l
Never use if the soldering iron is damaged.
l
Never expose to heat above 50
°
C and avoid prolonged exposure
to the sun.
l
Never puncture or incinerate.
l
Never refill, ignite or use near flame or combustible materials.
l
Never replace cap without first switching off and ensuring the tip
has cooled.
l
Never attempt to dismantle, readjust or repair. The soldering iron
is not user serviceable.
l
Never “carry on” or “check in” baggage containing this item
without confirming with the airline first that this is acceptable.
Ignition switch ( )
Gas inspection
window
Filling valve
Temperature
regulating dial
Fig. 2
I
(ON)
o
(OFF)
Gas ON-OFF switch
Soldering tip
Fig. 1
INSTRUCTION MANUAL
www.kennedy-tools.co.uk
Exhaust ports
TIP TEMPERATURE RANGES
Soldering:
580
°
C
Blow torch:
1,300
°
C
Hot air:
625
°
C
Hot knife:
580
°
C
Tip retaining collar
Front end
burner
Tip
Tip retaining
collar
Soldering iron
Tip retaining
tube
Fig. 3
