INSTALLATION / OPERATING
INSTRUCTIONS FOR WIRELESS DIGITAL
PROGRAMMABLE THERMOSTAT
- THPW
1-
C*
GENERAL
INSTALLATION
OPERATION AND PROGRAMMING INSTRUCTIONS
The THPW
1-C*
digital programmable thermostat consists of the
thermostat transmitter and the remote mains operated receiver
unit.
It has
7
days preset programs which can be tailored to suit your
lifestyle.
The THPW
1
-C* transmitter is operated by
2
x AA size batteries
and can replace any mechanical standard
2
wire thermostat.
Please note that the maximum resistive load is
16
A.
These units are paired during manufacture and the operating
channel is given by a letter code. When installing more than one
unit in a system ensure each thermostat pair has a different letter
code.
SAFETY INSTRUCTIONS
Please read these instructions fully before
attempting installation.
IF IN DOUBT, INSTALLATION SHOULD BE MADE BY A
QUALIFIED ELECTRICIAN IN ACCORDANCE WITH
CURRENT WIRING REGULATIONS.
1.
You should place the thermostat as following:
a. About
160
cm up from the floor.
b. Only on inside walls (not on an outside wall).
c. Do not expose to direct sun light.
d. Do not position close to a heater, ventilation outlet or
close to an outside door.
2.
Remove the front cover. Unscrew the screw in the battery
compartment. Remove the front housing from the base.
3.
Using the base as a template, drill two holes in the wall and
secure the base with appropriate wall plugs and screws.
4.
Replace the front housing onto base and replace the screw
in battery compartment.
5.
Install
2
x AA size batteries into battery compartment and
replace front case.
6.
Press the reset button once to enter time set mode.
Features of the LCD display and keys:
THPW
1-
C LCD display
Fig
1
Fig
3
Fig
2
To view programs:
THPW
1-C*
thermostat is a weekly programmable thermostat,
and each day can be programmed separately.
Each hour can select
or
temperature. However a weekly
factory preset program is installed.
This preset program is set to suit most families life style. See
table
3.1
for factory preset program.
Description of each key function:
- To enter into program mode
- To view
an
Temperatures
- To enter into time and day adjustment mode
Reset - To reset the unit into initial mode
- To turn the unit on or off
- To enter into Vacation mode
- To confirm setting
- To override into CT (COMFORT Temperature) mode (
20
°C)
- To override into ET (ECONOMY Temperature) mode (
17
°C)
- Temporary temperature override mode or increase
value adjustment
- Temporary temperature override mode or decrease
value adjustment
Press
key. The Monday preset program at
0.00
is on display.
Press
or
key the display will show the temperature setting in
each hour. E.g. Monday program show
0:00
-
5:59
and
8:00
-
15:59
are set at evening temp.,
6:00
-
7:59
and
16:00
-
22:59
is
set at CT. Note
23:00
-
0:00
is set at ET.
Press
key the next day preset program is displayed. Again
Press
or
key. This will show the temperature setting at each
hour. Repeat above steps, each preset program will display until
Sunday. Once Sunday program has been reviewed. Press
key.
The display will return into running mode.
To set clock and day:
After the batteries (
2
x AA size) have been installed into the
thermostat unit, or reset or
key is pressed, the thermostat is
in time adjustment mode.
The hour is flashing. Press
or
key to adjust hour.
Press
key to confirm setting. The minute is flashing.
Press
or
key to adjust minute. Press
key to confirm
setting. The day is flashing. Press
or
key to adjust day.
Press
key to confirm setting. This will
confirm the setting of time and day.
The display will return into running mode.
E.g. If you have set the clock at
8
.
30
FRIDAY
and the room temperature is
25
°C.
The display will display in Fig
3
.
To change preset program:
The preset program may not be suitable for some families but
the program may be adjusted to suit your living life style.
The following instruction will allow you to change the preset
program.
Press
key to enter into program viewing mode.
Press
key to select the day of program to make a change.
Press
or
key to select the hour to make change. Press
or
to select the temperature to make change. E.g. To change
Saturday
12:00
-
16:59
from CT to
12:00
-
16:59
ET.
1
.
Press
key to enter into program viewing mode.
2
.
Press
key to select the day to Saturday program.
3
.
Press
key until
12:00
with CT setting.
4
.
Press
key to change CT period to ET period.
5
.
Repeat step
3
&
4
to change
13:00
-
14:00
from CT period to
ET period.
6
.
Press
key to confirm setting. Press
key to return into
running mode.
7
.
You can review the program on
Saturday to check the program and
confirm the setting (Fig
4
).
Fig
4
Mode
Air-conditioning
Heating
23
°
c
20
°
c
28
°
c
17
°
c
Important
Note: Do not set the beginning and end of the program to
0
:
00
due to the thermostat needing this time for its reference use.
Therefore you must set the beginning or end time at
23
:
00
or
01
:
00
.
To view and change
or
temperature:
The CT and ET temperature is preset at below table for heating
and air-conditioning mode:
Fig
3.1
Part numbers:
THPW
1
-CA, THPW
1
-CB, THPW
1
-CC, THPW
1
-CD, THPW
1
-CE
Our latest microprocessor controlled programmable thermostat
has been designed to reduce your heating and air-conditioning
bill. The THP
W1
-C* is made to be user friendly and easy to use.
THPW1-C* Instructions July 2012:Layout 1 30/7/12 10:59 Page 1
