background image

Congratulations on being an owner of a versatile 

KIOTI DK45, DK50

t r a c t o r. This tractor has been

designed with finest materials and under a rigid quality control standards set forth by 

K I O T I

e n g i n e e r i n g

department. Knowledge of tractor operation is essential for many years of dependable service and

r e l i a b i l i t y. This manual is given to help you familiarize yourself with the 

DK45, DK50

tractor and to give

you helpful information about tractor safety, operation and maintenance. It is 

K I O T I

policy to provide each

K I O T I

tractor owner with a detailed owner’s manual to help you answer many questions. If the

information you are seeking is not found in this manual, your 

K I O T I

tractor dealer will be happy to help

you. Please feel free to contact 

DAEDONG-USA, INC.

Throughout this manual, you will see text in italics, preceded by the words 

NOTE, IMPORTA N T

o r

WA R N I N G

. Such text has the following significance.

NOTE :

This text stresses a correct operating procedure or technique.

I M P O R TANT :

This text stresses a correct operating technique or procedure that, If ignored, could result

in damage to the tractor or equipment.

WARNING :

This text stresses a correct operating technique or procedure that, if ignored,

could result in personal injury or death to the operator or bystanders.

Foreword

Summary of Contents for DK45





























































Reviews: