background image

GAS-FIRED INFRARED   

OUTDOOR PATIO HEATER   

                                                                           

INSTALLATION, OPERATION

         

MAINTENANCE INSTRUCTIONS 

 

 

 
 
 
 
 
 

FOR MODEL PTH106A-SS 

 

TABLE OF CONTENTS

                                                                                                     

PAGE 

IMPORTANT …………………………………………………………………… 

 

  1 

TOOLS & PARTS ……………………………………………………………….. 

 

  2   

PRECAUTIONS…………………………………………………………………..   

 3     

ASSEMBLY INSTRUCTIONS …………………………………………………. 

 

  4     

GAS REQUIREMENTS & LEAK TESTING ………………………………….. 

 

  7   

SAFETY CHECKS ……………………………………………………………….   

  8 

LOCATING HEATER FOR USE ………………………………………………. 

 

  9 

LIGHTING / SHUTDOWN ……………………………………………………….       10 
STORAGE / BURNER REMOVAL………………………………..…………….   

  12 

BURNER INSTALLATION / PILOT CLEANING ………………………………            13 
BURNER REMOVAL …………………………………………………………….   

 14  

TROUBLE SHOOTING .…………………………………………………………   

  15 

PARTS LIST ………………………………………………………………………       16 
WARRANTY ………………………………………………………………………       17 

 

READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND BE SURE YOUR PATIO HEATER IS 
PROPERLY INSTALLED, ASSEMBLIED AND CARED FOR. FAILURE TO FOLLOW THESE 
INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. IF 
YOU HAVE QUESTIONS CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR 
DEALER, GAS APPLIANCE SERVICE REPRESENTATIVE OR YOUR GAS COMPANY. 

 

NOTE TO INSTALLER:   
LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION.   

 

NOTE TO THE CONSUMER:   
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.   

 

 

STOP 

PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE   
DO NOT RETURN TO PLACE OF PURCHASE

 

 

Summary of Contents for PTH106A-SS



















Reviews: