background image

Hardware List

Part List

9

Tool(s) required for assembly: Phillips screwdriver, Level

IMPORTANT

Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.

Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

20 05530 0553

Bunk Bed

Cartons 20 05530 0551 and 0552 are also needed for assembly.

Small Hex Wrench

1 pc.

Hex Wrench

1 pc.

M6x40
Head Cap Bolt

20 pcs. (+1 extra)

Angled Washer

16 pcs. (+1 extra)

M6x30
Head Cap Bolt (short)

10 pcs. (+1 extra)

M6x70
Head Cap Bolt (medium)

6 pcs. (+1 extra)

Cross Dowel

8 pcs. (+1 extra)

M6x90
Head Cap Bolt (long)

2 pcs. (+1 extra)

Metal Pin

4 pcs.

M8x25
Wood Screw

56 pcs. (+1 extra)

K.
Front Guardrail

2 pcs.

L.
Back Guardrail

2 pcs.

M.
Rail

2 pcs.

N.
Leg

2 pcs.

O.
Support

2 pcs.

P.
Support

1 pc.

M6x60
Head Cap Bolt
for Leg

2 pcs. (+1 extra)

I.
Upper Front Panel

1 pc.

G.
Lower Front Panel

1 pc.

H.
Lower Back Panel

1 pc.

J.
Upper Back Panel

1 pc.

Q.
Ladder

1 pc.

Summary of Contents for 20 05530 0553










Reviews: