background image

TT-1651 4/17a

INSTALLATION INSTRUCTIONS

Original Issue Date:

4/15

Model:

13EKOZD/11EFKOZD, 15EKOZD/13EFKOZD, 16.5/17.5/19.5/20EFKOZD,

20EKOZD/17.5-16.5EFKOZD, and 23EKOZD/20-19.5EFKOZD

Market:

Marine

Subject:

Sound Shield Kits with Front Connection Panel GM93548-KP1,

GM93548-KP2, GM93548-KP3, GM93548-KP4, GM95106-KP1, and

GM95106-KP2

Introduction

The sound shield quiets operation of generator sets

used in marine applications. When installing the sound

shield, follow the installation procedure and observe the

safety precautions listed below. See Figure 1 for kit

selection.

Take into consideration the minimum clearance for

vibration and cooling during operation. For sound

shielded units, allow 305 mm (12 inches) minimum

clearance for the service and non-service side doors

(intake and discharge openings).

Model

Kit Number

13EKOZD/11EFKOZD

GM93548-KP1

15EKOZD/13EFKOZD

GM93548-KP4

17.5/16.5EFKOZD

GM93548-KP2

20EKOZD

GM95106-KP1

20/19.5EFKOZD

GM93548-KP3

23EKOZD

GM95106-KP2

Figure 1

Sound Shield Kit Selection

Safety Precautions

Accidental starting.

Can cause severe injury or death.

Disconnect the battery cables before

working on the generator set.

Remove the negative (--) lead first

when disconnecting the battery.

Reconnect the negative (--) lead last

when reconnecting the battery.

WARNING

Disabling the generator set. Accidental starting can

cause severe injury or death.

Before working on the

generator set or equipment connected to the set, disable the

generator set as follows: (1) Press the generator set off/reset

button to shut down the generator set. (2) Disconnect the

power to the battery charger, if equipped. (3) Remove the

battery cables, negative (--) lead first. Reconnect the negative

(--) lead last when reconnecting the battery. Follow these

precautions to prevent the starting of the generator set by the

remote start/stop switch.

Risk of fire.

Can cause severe injury or death.

Do not smoke or permit flames or

sparks near fuels or the fuel system.

WARNING

Servicing the fuel system. A flash fire can cause severe

injury or death.

Do not smoke or permit flames or sparks near

the fuel injection system, fuel line, fuel filter, fuel pump, or other

potential sources of spilled fuels or fuel vapors. Catch fuels in

an approved container when removing the fuel line or fuel

system.

Summary of Contents for 11EFKOZD













Reviews: