background image

1

DEAR CUSTOMER 

 

You have purchased heating boiler manufactured by Ukrainian State 

Enterprise “Krasilov aggregate plant”. To guarantee a long-time failure-free 
and safe operation of your boiler we request always to follow the further 
mentioned information.

 

 
1. SAFETY INSTRUCTION: 

 
This manual contains important information for the safe and correct 

installation, start-up and trouble-free operation and maintenance of the 
heating boiler.  

The heating boilers should be used for heating rooms and preparing food 

only in the manner described in this manual. 

Make sure that you purchased the heating boiler of necessary power that 

corresponding with heating project documentation of your house or 
premises.  

 
USE only original “KORDI” parts 
 
1.1.

 

Instruction to boiler installer: 

 

During installation and operation, the country specific requirements and 

regulations must be observed: 
-

 

local construction regulations on the installation, air supply and exhaust 
gas extraction as well as chimney connection. 

-

 

regulations and norms concerning the fitting of the heating installation 
with safety devices. 

 
1.1.1.

 

Safety rules for user operation: 

 

-

 

operate the heating boiler at a maximum temperature of 95ºC, in order to 
prevent overheating use the cooling coil. When the temperature in a 
boiler reach 95 ºC the thermostatic valve will open and the cold water 
from water mains passes through cooling coil and cools the heating 
system; 

-

 

the maximum allowable pressure in the boiler is 2 bars. Install relief 
valve and thermomanometer in order to check the temperature water 
pressure. They should be installed on the mounting places on the back 
side of the boiler; 

-

 

do not use flammable liquids for ignition or increase of burner output; 

-

 

collect ash in fireproof container covered with lid; 

Summary of Contents for Kordi-10S





















Reviews: