background image

RCL-336

Larson Electronics, LLC

 

 Phone: (800) 369-6671 

Fax: (903) 498-3364 

www.larsonelectronics.com 

1

 of 

1

0

 

Remote Control Thermal Imaging Camera System - 12V - Wireless 

or Wired Remote - 6" LCD Monitor

 Instruction Manual 

Please read these instructions before using your new 

remote control thermal imaging camera system

.

The 

camera's

 wireless remote are designed to be attached to a vehicle using a magnetic or per-manent mount and 

operated by a wireless remote control.  Each spotlight has 3

6

0° horizontal rotation and 135° vertical tilt.

Introduction 

The Thermal Imaging Camera System can help a driver identify pedestrians in front of their vehicle during low light 

situations. The Thermal Imaging Camera System is capable of identifying the objects generating heat, displaying them 

on a screen, and improving the driver’s experience. 
The infrared thermal imager detects infrared energy (heat) through a non-contacting method, converts it to an electric 

signal, and generates a thermal image that appears on a screen. The infrared thermal imager is an inspection device 

which can be used to calculate the temperature. It can also precisely quantize and measure the detected heat, so that 

you can observe the thermal image and accurately identify animals and pedestrians. 
Per the statistics of the National Highway Traffic Safety Administration, while night driving only accounts for 25% of total 

road traffic, the number of fatal accidents accounts for 50%. This makes having the Thermal Imaging Camera System 

an important safety accessory for any driver. 

Product Overview 

 

Object Identification

: Identify animals and pedestrians during low light situations. 

Animal Detection 

Pedestrian Detection 

Animal Detection 

Pedestrian Detection 

Summary of Contents for RCL-336











Reviews: