background image

 

 

User

s Manual 

For 

DCS810S 

Digital DC Servo Driver 

Revision 1.0 

©

2009 All Rights Reserved 

Attention: Please read this manual carefully before using the driver! 

 

3/F, Block 2, Nanyou Tianan Industrial Park, Nanshan Dist, Shenzhen, China 

Tel: (86)755-26434369      Fax: (86)755-26402718 

URL: 

www.leadshine.com

      E-Mail: 

sales@leadshine.com

 

 

 

The content in this manual has been carefully prepared and is believed to be accurate, 

but no responsibility is assumed for inaccuracies. 

Leadshine reserves the right to make changes without further notice to any products 

herein  to  improve  reliability,  function  or  design.  Leadshine  does  not  assume  any 

liability  arising  out  of  the  application  or  use  of  any  product  or  circuit  described 

herein; neither does it convey any license under its patent rights of others.   

Leadshine

s  general  policy  does  not  recommend  the  use  of  its  products  in  life 

support or aircraft applications wherein a failure or malfunction of the product may 

directly  threaten  life  or  injury.  According  to  Leadshine

s  terms  and  conditions  of 

sales,  the  user  of  Leadshine

s  products  in  life  support  or  aircraft  applications 

assumes all risks of such use and indemnifies Leadshine against all damages. 

 

 

 

 

 

 

 

 

 

©

2009 by Leadshine Technology Company Limited. 

All Rights Reserved

Summary of Contents for DCS810S













Reviews: