background image

LISTED

 

use only with

Class 2 Type

power units

24V

DC  Power

4.4

WATTS

FOOT

Safety & Warnings

THREE YEAR LIMITED LIGHTING WARRANTY

LED WORLD INC. warranties this product for three year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other 
warranties expressed or implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This 
Limited Warranty does not apply to damage caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims 
must be submitted to them. This product must be used with LED World’s class 2 power supply. Failure to do so will void limited warranty.

LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected 
with, the purchase of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or 
otherwise, or economic loss, under any theory of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing 
(including without limitation gross negligence and fundamental breach) by led world inc or any person for whom led world inc is responsible, and even if led world inc has been advised of the 
possibility of such loss or damage being incurred.

If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return 
authorization number.

1/4

KG

Never Nail or use Staples

Only power with 24VDC
Class 2 Power Source

Never apply weights or walk on strips

RGB LED FLEX STRIP

  

Model: 

FA60M50-5M-24V-RGB

 (RGB: Red, Green, Blue)

 

Ÿ

Do not power when rolled

. Lighting must be installed in a straight line. Do not curl or twist and roll out completely straight before applying power.

Ÿ

Only install on smooth at surfaces free of burrows that are re retardant.

Ÿ

Product has an adhesive tape on back. Adhesion can only be made once and the LED strip must 

fully adhere to surface

 (ush). Failure to do this step will 

damage product. Rigidly support wires with wire clamps.

Ÿ

During installation, do not damage the printed circuit. Exposed wires can cause short circuit damaging product and creating a serious hazard. Do not mount in 
a manner or support LED Strip light in a manner that can damage the outer jacket or cord insulation. Do not install this lighting system where the exposed bare 
conductors can be shorted or contact any conductive materials. Carefully check that there is no wire cross-over or possibility in the future in area of installation.

Ÿ

To reduce the risk of re and overheating, make sure all connections are tight.

Ÿ

Product is sold in the maximum length. 

Do not exceed or extend the length of the roll.

Ÿ

Only qualied electrician or engineer can perform installation familiar with low voltage wiring techniques. Correct polarity is imperative (+/- is marked on printed 
circuit). Parallel connection only.

Ÿ

DO NOT install on ammable material or possibility of in the future. Do not install any luminaire closer than 6 inches (15.25 cm) from any curtain, or similar 
combustible materials.

Ÿ

The light and all its components cannot be mechanically pressed. Never apply to surface above 40c (104F).

Ÿ

Voltage must not exceed 

24VDC

 and must be regulated. The Voltage is printed every 6 LEDS. Check that it is the correct voltage before applying power.

Ÿ

This is not a toy. Keep out of children's reach.

Ÿ

Keep Flex strip spaced ¾” apart if placing next to each other.

Ÿ

LED Flex Strip is bendable on one at widest plane. Maximum bend radius is 4 inches (100mm) on one plane (at).

Ÿ

Not for use in mission critical, aircraft, emergency signs or lifesaving equipment.

Ÿ

Static electricity can damage LED(s). Handle with care.

Ÿ

Inspect installation after one hour and thereafter regularly.

Ÿ

For stationary use only and not subjected to possible pressure or movement (or in the future).

Ÿ

Not for in-wall use.

Ÿ

Max. Soldering temperature cannot exceed 250

°

C (482

°

F) for a max of 4 seconds. Use 22~20 AWG wire to connect.

Ÿ

Use correct wiring as required by local electrical code. Use a 20 gauge wire to attach to strip by solder (2464 type of wire). Connection to power source may use 
Wago™ 222-413 in hardwire applications.

Ÿ

Cable lighting systems not be installed in bathrooms.

Ÿ

Conductors of extra-low-voltage circuits be rigidly supported.

Ÿ

Conductors not be installed in contact with combustible materials and not run through walls, ceilings, oors or partitions, and; Uninsulated conductors not be 
installed less than 2.2 m (86”) from the oor.

Ÿ

Do not stare 

directly 

into the LED Light. Install LED lighting out of direct sight.

Use only with LED World’s Class 2 Type power supply.
Indoor use, Dry locations. Do not expose LED Flex Strip to moisture.
Disconnect power before installing or servicing (at breaker point).
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local regulations. 
Only power with a (listed) constant voltage Class 2 power supply (24V DC).
Never plug into 120V AC. The product requires a optional class 2 Transformer.

1-800-387-4081

 

ledworldlighting.com ledworld.ca

 | 

Apply  to  surface  at  room  temperature.  Keep
a w a y   f r o m    a m m a b l e   m a t e r i a l s .   S u r f a c e
temperature MAX 40

°

C (104

°

F). Don’t install under,

above or near heat sources (i.e. stoves, replaces) 

IMPORTANT INSTRUCTIONS

Please read instructions before using product and 

SAVE THESE INSTRUCTIONS

. Before using this product make sure you have right color, product 

(item number) and voltage (printed on product). Check for possibility of damage during shipping. If damaged, or wrong product, 

do not use

Disconnect power before installing or using.  

Use only with Class 2 Type power supply. Using with any other type of power supply will void the limited warranty.

STATIC ELECTRICITY

CAN DAMAGE 

PRODUCT

Copyright © 2017 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 2.7 - 03/07/17

Summary of Contents for FA60M50-5M-24V-RGB

Page 1: ... perform installation familiar with low voltage wiring techniques Correct polarity is imperative is marked on printed circuit Parallel connection only Ÿ DO NOT install on ammable material or possibility of in the future Do not install any luminaire closer than 6 inches 15 25 cm from any curtain or similar combustible materials Ÿ The light and all its components cannot be mechanically pressed Never...

Page 2: ...commend design steps before starting the installation process General questions based on lighting requirements Ÿ Where will your power supply be located Ÿ How will you switch your LED lighting ON and OFF Ÿ What is the best layout con guration for your installation with wiring consideration Ÿ How will you run your wiring to your LED strip lighting WATTAGE CALCULATION The LED Flex Strips have a labe...

Page 3: ...are be cuttable at each 3 LEDs Cut marks lying between set of soldering points CONNECT WITH RGB QUICK CONNECTORS SOLDERING There are many options available for connecting LED light strips Right diagram shows how connect using our RGB Quick Connectors However it is strongly recommend to solder the connection Please refer to our quick connector instruction sheet Soldered Contacts G R B G R B G R B G...

Page 4: ...rips Ÿ Consider testing with a multimeter to ensure light strip is receiving 24V power LED Flex Strip lights blink on then go off Ÿ The power supply is not adequate for the length of LED Light Strips you are powering Install a adequate Class 2 power supply LEDs farthest from the power supply are noticeably dimmer Ÿ This is the result of voltage drop Decrease the length of the 24V power feed or use...

Reviews: