background image

 

 
 
 
 
 

 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 

 

 

LXB-L15C

 

 

 

 

USER MANUAL 

 

TABLE OF CONTENTS

 

 

FOR YOUR SAFETY --------------------------------------------------  1 

SAFETY PRECAUTIONS --------------------------------------  2 
SPECIAL NOTES ON LCD MONITORS -------------------  3 

 

BEFORE YOU OPERATE THE MONITOR ---------------------  3 

FEATURES --------------------------------------------------------  3 
PACKING LIST ---------------------------------------------------  3 
CONTROLS AND CONNECTORS -----------------------  4-5 
ADJUSTING THE VIEWING ANGLE -------------------- 

 

5-6 

 
 

OPERATING INSTRUCTIONS -------------------------------------  7 

GENERAL INSTRUCTIONS ----------------------------------  8 
HOW TO ADJUST A SETTING ------------------------------  9 
ADJUSTING THE PICTURE ------------------------------

 

9-10 

PLUG AND PLAY -----------------------------------------------

  

11 

 

TECHNICAL SUPPORT(FAQ) -------------------------------

  

12-13 

ERROR  MESSAGE & POSSIBLE  SOLUTION -------

 

 

14 

 

APPENDIX --------------------------------------------------------------

 

15 

SPECIFICATIONS -----------------------------------------

  

15-16 

FACTORY PRESET TIMING TABLE ----------------------

 

17 

CONNECTOR PIN ASSIGNMENT -------------------------

 

17 

 
 

 

 

  

English 

Deutsch 

Françai 

Español 

Italian

 

 

 

TCO’95

 

Summary of Contents for LXB-L15C




















Reviews: