WARNING AND CAUTIONS:
• TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS
• IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT AN ELECTRICIAN.
• TO AVOID FIRE, SHOCK, OR DEATH;
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF
BEFORE WIRING.
• INCORRECT ASSEMBLY OR INSTALLATION MAY RESULT IN FIRE, ELECTRICAL PROPERTY DAMAGE, SHOCK, PERSONAL INJURY, OR DEATH.
• A SURGE PROTECTIVE DEVICE IN A FEED-THROUGH BRANCH CIRCUIT WILL PROVIDE PROTECTION ONLY FOR LOADS WIRED DIRECTLY TO
IT. IT WILL NOT PROVIDE PROTECTION TO ANY OTHER DEVICES ON THE SAME BRANCH CIRCUIT.
• USE THIS DEVICE WITH
COPPER OR COPPER CLAD WIRE ONLY.
DESCRIPTION
Leviton Surge Protective Device (SPD) module, Cat. No. 3801-DIN is intended for use with sensitive electronic equipment, such as Industrial Control Panels,
electronic analysis and monitoring equipment and other applications with solid state circuitry that would benefit from protection against damage caused by
transient surges.
FEATURES
• This device is intended for single branch circuits only.
• The indicator light denotes surge suppression is effective when it is continuously ON.
• This device does not supply ground fault or overload protection.
• This device protects against surges at this module only.
• When the indicator light turns OFF, the device is no longer providing suppression. The entire unit must be replaced, if surge suppression is required.
•
Power continues to be supplied to the receptacle/output screw terminals in the event of a surge suppression circuit failure.
• Modules should be replaced as soon as possible, after a failure is noted.
Solid state semi-conductor SPD circuitry for:
• 3801-DIN (Line to Neutral, Line to Ground and Neutral to Ground protection).
• SPD is enclosed in a non-conductive ABS case. ABS is a flame retardant thermoplastic, compliant with UL 746C polymeric material test requirements.
• SPD is intended to supply 125 VAC to plug-in equipment while providing feed-through capability for hard-wired 125 VAC equipment
(see Figs. 1 & 2).
TO INSTALL
Location and Mounting:
1.
WARNING:
TURN OFF POWER AT THE INSTALLATION LOCATION.
2. Locate the SPD so that its hard-wired or plug-in connections can be easily connected to AC Power without excessive tension on the wiring connections.
Use the two slotted “feet” or the DIN Rail clip to mount housing.
3. Connection of the SPD to chassis ground may be done via the wiring terminals (see Figs. 1 & 2). Grounding for the SPD can also be provided by using
the metallic base plate and/or the attached braided cable.
DO NOT ADD ANY EXTENSION TO THE “BRAIDED CABLE TO GROUND” PATH.
Wiring Procedure:
WARNING:
VERIFY THAT EQUIPMENT POWER AT THE SPD INSTALLATION LOCATION HAS BEEN
TURNED OFF.
NOTE: Power cabling used for 3801-DIN connections should be the same as that used to connect the equipment where protection is desired.
A short version of this cable should be prepared for connection between the OUTPUT “Line, Neutral, Gnd” terminals for the 3801-DIN and the INPUT
to the equipment.
1. Connect the power input cable previously used for connection to equipment to the SPD’s three terminals indicated in Fig. 2.
Note: Fig. 2 shows an organized connection. Actually, due to the parallel SPD circuit, there is no dedicated Input or Output screw terminals.
2. If protecting hard-wired equipment, connect one end of the short power cable to the remaining three screw terminals (see Fig. 2).
3. If protecting corded equipment, plug-in the AC power plug into the front of the 3801-DIN.
4. Connect the other end of the short cable to the equipment to be protected.
POWER ON: After reconnection of the equipment, restore power to the installation circuit by turning the input power ON.
INSTALLATION IS COMPLETE.
INSTALLATION
ENGLISH
DI-000-03801-20C
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
LIMITED 10 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and
proper use for ten years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such ten year period the product is returned prepaid, with proof
of purchase date, and a description of the problem to
Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747. This warranty excludes
and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened,
abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions.
There are no other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for
a particular purpose, is limited to ten years.
Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment,
lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
SURGE PROTECTIVE DEVICE (SPD)
Cat. No. 3801-DIN
Rated: 10A-125 VAC
DIN Rail Mounted
Fig. 1 - 3801-DIN Terminal Connections / Raccordement du 3801-DIN /
Conexiones Terminales de 3801-DIN
6-Pin Terninal Connector (1 Provided)
Connecteur à 6 broches (1 fourni)
Conector terminal de 6 pines (se suministra 1)
6 Pin Header
Collecteur à 6 broches
Cabezal de 6 pines
Receptacle for Connecting
Corded Equipment
Prise pour appareils enfichables
Receptáculo para conectar
equipos de cordones
Fig. 2 - 3801-DIN Polarized Plug-In Connector Wiring / Raccordement du 3801-DIN au moyen des connecteurs polarisés /
Cableado de Conector Enchufable Polarizado 3801-DIN
3801-DIN PLUG-IN
Connecteurs du 3801-DIN
Conector Enchufable 3801-DIN
From AC Power Input
Entrée d'alimentation c.a.
Entrada de Energía de la CA
AC Power Output (to equipment to be protected)
30-12 AWG solid or 24-16 AWG stranded copper wire
Sortie d'alimentation c.a. (vers l'appareil à protéger)
Fil de cuivre plein de calibre 30 à 12 AWG ou toronné de calibre 24 à 16 AWG
Salida de Energía de CA (al equipo que se va a proteger)
Cable de cobre sólido calibre 30-12 AWG o entrelazado 24-16 AWG
Gnd*/MALT*/Tierra*
Gnd*/MALT*/Tierra*
Neutral*/Neutre*/Neutro*
Neutral*/Neutre*/Neutro*
Line*/Ligne*/Línea*
Line*/Ligne*/Línea*
Green/Vert/Verde
Green/Vert/Verde
White/Blanc/Blanco
White/Blanc/Blanco
Black/Noir/Negro
Black/Noir/Negro
Screws are on connector side (torque: 5-7 in-lbs)
Les vis sont du côté des connecteurs
(couple de 5 à 7 po-lb)
Los tornillos están en el lado del conector
(tensión de 5-7
)
AC Power Cord
Fil d'alimentation c.a.
Cordón de Energía CA
AC Power Cord
Fil d'alimentation c.a.
Cordón de Energía CA
