background image

1

dc2048af

DEMO MANUAL DC2048A

Description

LTC3330EUH

Nanopower Buck-Boost DC/DC with

Energy Harvesting Battery Life Extender

Demonstration  Circuit 2048A  is  a  nanopower  buck-

boost DC/DC with energy harvesting battery life extender 

featuring the 

LTC

®

3330

. The LTC3330 integrates a high 

voltage  energy  harvesting  power  supply  plus  a  DC/DC 

converter powered by a primary cell battery to create a 

single output supply for alternative energy applications. 

The  energy  harvesting  power  supply,  consisting  of  an 

integrated low-loss full-wave bridge with a high voltage 

buck converter, harvests energy from piezoelectric, solar 

or  magnetic  sources.  The  primary  cell  input  powers  a 

buck-boost converter capable of operating down to 1.8V 

at its input. Either DC/DC converter can deliver energy to 

a single output. The buck operates when harvested energy 

is available, reducing the quiescent current drawn on the 

L

, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and Dust 

is a trademark of Linear Technology Corporation. All other trademarks are the property of their 

respective owners.

BoarD photo

battery  to  essentially  zero.  The  buck-boost  takes  over 

when harvested energy goes away.
A  low  noise  LDO  post  regulator  and  a  supercapacitor 

balancer are also integrated, accommodating a wide range 

of output storage configurations.
Voltage and current settings for both input and outputs 

are programmable via pin-strapped logic inputs.
The LTC3330EUH is available in a 5mm × 5mm 32-lead 

QFN surface mount package with exposed pad. 

Design  files  for  this  circuit  board  are  available  at  

http://www.linear.com/demo/DC2048A

Figure 1. DC2048A Demo Board

Figure 2. Typical Efficiency of DC2048A. 

Buck Efficiency vs I

LOAD

I

LOAD

 (A)

EFFICIENCY (%)

DC2048A F02

100

90

60

80
70

40

50

20

10

30

0

10µ

10m

100m

1m

100µ

V

OUT

 = 1.8V

V

OUT

 = 2.5V

V

OUT

 = 3.3V

V

OUT

 = 5V

V

IN

 = 6V, L = 22µH, DCR = 0.19Ω

Summary of Contents for DC2048A

















Reviews: