Litex Industries VN52 Installation Manual Download | Manualshive

Page: 1 / 11

background image

Installation Guide

For Model:

VN52

Table of Contents:

Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pgs. 4 - 5
Wiring. pg. 6
Canopy Assembly. pg. 6
Blade Assembly. pg. 7
Light Kit Assembly (Optional). pgs. 7- 8
Testing Your Fan. pg. 9
Troubleshooting. pg. 10
Parts Replacement. pg. 10
Warranty. pg. 10

net weight of fan: 17.22 lb. (7.81 kg)

E124404

READ THESE INSTRUCTIONS AND

SAVE THEM FOR FUTURE USE

PRINTED IN CHINA

1
2
3
...
»

Summary of Contents for VN52












Reviews:

No comments

Related manuals for VN52

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 16

Brand: Craftmade Pages: 26

Brand: Hunter Pages: 9

Brand: TI Pages: 4

Brand: Armstrong Air Pages: 25

Brand: Faro Barcelona Pages: 20

Brand: HAMPTON BAY Pages: 28

Brand: Linea 2000 Pages: 32

Brand: Sonnenkonig Pages: 40

WOOZOO PCF-MKC18

Brand: Ohyama Pages: 84

Brand: ebm-papst Pages: 13

Brand: Cumberland Pages: 2

Brand: Genesis Pages: 9

Brand: Powerfist Pages: 20

ECA 100 ipro KVZC

Brand: Maico Pages: 6

Brand: Neostar Electronics Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands