APPROVAL
ENG.
MKT.
Q.C.
OF
PG.
DR.
DATE
CHANGE DESCRIPTION
INSTRUCTION SHEET
PART NUMBER
SIZE:
CN. NO.
REV.
8.5 X 11 - ONE SIDE
11 X 17 - FOUR SIDES
8.5 X 11 - TWO SIDES
Information below is for Lithonia Lighitng documentation purposes only,
DO NOT
include in Instruction sheet art.
1
1
EMCSA00601
ELU 4/ELU 4N/ELU 8 EMERGENCY LIGHTING
UNIT
A
INITIAL RELEASE
MRS
INSTALLATION INSTRUCTIONS
ELU 4/ELU 4N/ELU 8
ELU 4/ELU 4N/ELU 8
ELU 4/ELU 4N/ELU 8
ELU 4/ELU 4N/ELU 8
ELU 4/ELU 4N/ELU 8
EMERGENCY LIGHTING UNIT
EMERGENCY LIGHTING UNIT
EMERGENCY LIGHTING UNIT
EMERGENCY LIGHTING UNIT
EMERGENCY LIGHTING UNIT
IMPOR
IMPOR
IMPOR
IMPOR
IMPORT
T
T
T
TANT SAFEGU
ANT SAFEGU
ANT SAFEGU
ANT SAFEGU
ANT SAFEGUARDS
ARDS
ARDS
ARDS
ARDS
1.READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
2. Do not use outdoors.
3. Do not let power supply cords touch hot surfaces.
4. Do not mount near gas or electric heater.
5. Use caution when servicing batteries. Battery acid can cause
burns to skin and eyes. If acid is spilled on skin or in eyes,
flush acid with fresh water and contact physician immediately.
6. Equipment should be mounted in locations and at heights
where it will not readily be subjected to tampering by unautho-
rized personnel.
7. The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
8. Do not use this equipment for other than intended use.
9. Before wiring to power supply, turn off electricity at fuse or
circuit breaker.
10. Refer to wiring diagrams for proper connections.
11. Consult your local building code for approved wiring.
12. Fixture must be grounded to avoid potential electric shock.
13. Disconnect AC power and unplug battery before servicing.
14. All servicing should be performed by qualified personnel.
15. CAUTION: Halogen cycle lamp(s) may be used in this fixture.
To avoid shattering, do not operate lamp in excess of rated
voltage. Protect lamp against liquids when lamp is operating.
Dispose of lamps with care. Halogen lamps operate at high
temperatures. Do not store or place flammable materials near
lamps.
SAVE THESE INSTRUCTIONS
CAUTION:
CAUTION:
CAUTION:
CAUTION:
CAUTION: For safety and proper operation, read and follow instructions carefully before installation.
PARTS DESCRIPTION
a
Housing
j
Clip
b
Hinged Front
k
Battery
c
Charger Board
l
Lamp Swivel
d
Hole Plug
m
Green Ground Screw
e
Terminal Board
(for battery chassis)
f
Lamp Bezel
n
Stop Washer
g
Lamp Housing
o
Lock Nut
h
Keyway Mounting Holes
p
Housing Slot
i
Closure Screw
q
Battery Chassis
NOTE: ELU 4N battery has polarized
connector rather than terminals
(not shown).
IMPORTANT: Provide each unit with a singleunswitched powersupply
from a 120V or 277V branch circuit used for normal lighting.
NOTE: Before installation, make sure unit is located to assure
adaquate clearance for the hinged front
b
and lamp head
g
orientation.
Do not position unit where it will be exposed to direct sunlight, radiators
or other heat sources. Prolonged exposure to high temperatures will
shorten battery life and void warranty.
*
( * ELU 4N ONLY)
SEE WIRING SCHEMATIC, FIGURE 3
