background image

101 N. Alloy Dr. 
Fenton, MI 48430

 

 

Ph (810) 

714-5811

Fax    (810) 714-5711

CustomerService@lmicorporation.com

 

 

Research, Development and Manufacturing of Precision Measuring Systems

 

 

Form:  CA 045 

5-05-05 

C:\Documents and Settings\timmartin\Local Settings\Temporary Internet Files\OLK9\CA 
045 LMI 241-BWV2 to 440 or 501.doc 

Page 1 of  

12 

 

CONFIGURATION and MASTERING for the 

LMI 241-BWV2 or 241-FG the LMI 440 or ASI DATAMYTE 501 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

This instruction will outline: 

I.

 

GAGE CONFIGURATION

....................................................................................................................................... 2

 

Flush Setup

............................................................................................................................................................ 2

 

Gap Setup

............................................................................................................................................................... 6

 

II.

 

MASTERING INSTRUCTIONS

.............................................................................................................................. 9

 

III.

 

VERIFICATION OF THE MASTERING

............................................................................................................. 11

 

Flush Verification

................................................................................................................................................ 11

 

Gap Verification

.................................................................................................................................................. 12

 

 

Required Equipment: 

1.

 

LMI 440 or ASI DataMyte 501 

2.

 

LMI 241BWV2 or 241-FG 

3.

 

LMI 6025 6 pin to 6pin cable 

4. LMI 3062 Master Block 

2

3

4

Summary of Contents for 241-BWV2













Reviews: