background image

ASIA PACIFIC

  

18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: +61 7 3854 5000 | F: +61 7 3854 5001 | Email: sales@lumascape.com.au | 

www.lumacape.com.au

NORTH AMERICA

  1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone +1 650 595 5862 | Fax +1 650 595 5820 | Email: info@lumascape.com | 

www.lumacape.com

1 / 9

 IN0206 N190610

Linealux 

L3

 

LS9031

Installation Instructions

Products and specifications are subject to change without notice.

LS9031

LS9031 

Linear Facade  
Lite

READ ALL SAFETY INSTRUCTIONS FIRST

 

› Follow instructions carefully, failure to do so will void 

warranty.

 

› Ensure installation complies with local law and 

applicable standards.

 

› Input voltage range 120-277 V

 

› Only use Lumascape power supply, control 

equipment and leader cables.

 

› Ensure mains input power is surge protected.

 

› Never make connections whilst the power is 

connected.

 

› Do not make modifications or alter the product.

 

› Keep luminaire clean and free of debris.

 

› Connectors are to be kept clean and dry at all times. 

 

› Once installed, all connectors are to be mated and a 

terminating plug is required on the last fitting of run.

Summary of Contents for Linealux L3 LS9031










Reviews: