background image

LUVERNETRUCK.COM

  

  

PRODUCT SUPPORT: 877.287.8634

  

  

570747-INS-RA

  

  

01/29/2021

  

  

ECN7969

  

  

PAGE 1

Product Registration and Warranty

LUVERNE stands behind our products with industry-leading warranties. To get copies of the product 

warranties, register your purchase or provide feedback, visit: 

warranty.curtgroup.com/surveys

INSTALLATION MANUAL

570747

Tools Required

Drill

Ratchet

Drill bit, 7/16”

Wrench, 1/2”

Drill bit, 7/32”

Straight edge 

or Level

Drill bit, 11/32”

Paint marker

Socket, 1/2”

Tape measure

Panel trim 

removal tool

--

Maintenance

Mild automotive detergent may be used to clean the product. Do not use dish detergent, abrasive 

cleaners, abrasive pads, wire brushes or other similar products that may damage the finish.

Product Photo

Front

Rear

Torque Specifications

5/16"

7 ft-lbs.

Use above torque setting unless otherwise noted

Level of Difficulty

Moderate

Installation difficulty levels are based on time 
and effort involved and may vary depending on 
the installer level of expertise, condition of the 
vehicle and proper tools and equipment.

Parts List

Item Qty Description

1

2

Mounting bracket, driver side 

2

2

Mounting bracket, passenger 

side front

3

3

Mounting bracket, passenger 

side rear

4

2

Mounting bracket, spacer

5

7

Retainer plate

6

17

Flat washer, 5/16”

7

17

Hex bolt, 5/16”-18 x 1”, grade 5 

8

16

Flange nut, 5/16”-18

9

4

Flat washer, 5/16”, 

black zinc plate

10

4

Hex bolt, 5/16”-18 x 1”, 

grade 5, black zinc plate

11

5

Clip on nut, 5/16”-18

12

4

Thread forming bolt, 5/16” x 1”

NOTICE

Visit 

www.luvernetruck.com

 for a full-color copy of this 

instruction manual, as well as helpful videos, guides and much more!
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
Periodic inspection of your product should be performed 

to ensure all hardware and / or components remain secure.
To help prevent damage to the product or vehicle, refer to the specified 

torque specifications when securing hardware during the installation process.

This is the first of two manuals 

required to complete this installation. 

The second manual is included with 

your side steps / running boards.  

Summary of Contents for 570747







Reviews: