background image

LUX PRODUCTS CORPORATION

Mt. Laurel, New Jersey 08054  USA

I M P O R T A N T !

Thank you for your confidence in our product. To obtain the
best results from your investment, please read these
instructions and acquaint yourself with your purchase
before installing your new thermostat. Then follow the
installation procedures, one step at a time.  This will save
you time and minimize the chance of damaging the
thermostat and the systems it controls.  These instructions
may contain information beyond that required for your
particular installation. Please save for future reference.

READ

INSTALLATION

INSTRUCTIONS

FIRST

PSP711RF SERIES

SMART TEMP

®

ELECTRONIC THERMOSTAT

HEAT

OFF

COOL

AUTO

ON

FAN

RESET

HOLD

NEXT

RUN

FILTER

SET

SUNDAY
PROGRAM

SET

SATURDAY
PROGRAM

SET

WEEKDAY
PROGRAM

SET

DAY/TIME

DOWN

UP

1500

P a t e n t s   P e n d i n g

MO

DAY

HEAT

PM

SIMPLIFIED INSTRUCTIONS

• Press UP/DOWN to set time.

TO SET PROGRAMS

• Rotate Dial to SET

WEEKDAY

TEMPORARY TEMPERATURE OVERRIDE

•Press UP/DOWN to adjust set temperature.
•To clear OVERRIDE press UP/DOWN until

original set temperature appears or wait for
the start tf the next period

TO SET TIME & DAY

• Rotate Dial to SET

DAY/TIME.

• Press UP to change

t d

HEAT

OFF

COOL

AUTO

ON

FAN

RESET

HOLD

NEXT

RUN

FILTER

SET

SUNDAY
PROGRAM

SET

SATURDAY
PROGRAM

SET

WEEKDAY
PROGRAM

SET

DAY/TIME

DOWN

UP

1500

P a t e n t s   P e n d i n g

MO

DAY

HEAT

PM

SIMPLIFIED INSTRUCTIONS

• Press UP/DOWN to set time.

TO SET PROGRAMS

• Rotate Dial to SET

TEMPORARY TEMPERATURE OVERRIDE

•Press UP/DOWN to adjust set temperature.
•To clear OVERRIDE press UP/DOWN until

original set temperature appears or wait for

TO SET TIME & DAY

• Rotate Dial to SET

DAY/TIME.

• Press UP to change

DOWN

UP

MO

DAY

HEAT

PM

Choose Heat or Cool

Set Day & Time

Installs Easily

Easy

as

1–2–3

INSTALLATION AND OPERATING

INSTRUCTIONS

WARNING:

Use Energizer

®

or DURACELL

®

Alkaline Batteries Only.

Energizer

®

is a registered trademark of Eveready Battery Company, Inc.

DURACELL

®

is a registered trademark of The Gillette Company, Inc.

• Press UP/DOWN

to set time.

TO SET TIME & DAY

• Rotate Dial to SET

DAY/TIME.

• Press UP to change

current day.

• Press NEXT.

TO SET PROGRAMS

• Rotate Dial to SET

WEEKDAY,
SATURDAY or
SUNDAY PROGRAM.

• Press UP/DOWN to adjust

start time.

• Press NEXT.
• Press UP/DOWN to adjust

temperature.

• Press NEXT.
• Repeat as needed or rotate

dial to RUN to stop Programming.

TEMPORARY TEMPERATURE OVERRIDE

•Press UP/DOWN to adjust set temperatur

PATENT NO. 5,673,850

e.

•To clear OVERRIDE press UP/DOWN until

original set temperature appears or wait for
the start tf the next period.

TEMPERATURE HOLD

• Press HOLD. Adjust temperature as

desired with UP/DOWN.

•To clear, press HOLD again.

SIMPLIFIED INSTRUCTIONS

The Active Program Period

Liquid Crystal 
Display

Fan Switch

System
Switch

Easy to 
follow 
Instructions

LUX Speed 
Dial

®

Thermostat
Body

The Set 
Temperature

Thermostat 
Cover

Button to Light
Display

FEATURES

52004

• 

The Unit can be used with most 24 volt gas, oil or electric heating and air

conditioning systems, single-stage heat pumps or gas millivolt heating

systems. It cannot be used with 120 volt heating systems or multistage heat
pumps. Ask your dealer for other LUX thermostats to control those systems.

• 

The Unit is programmable. There are four programming periods per day. Each
period can be programmed separately.

• 

You can use the built-in time/temperature programs, or alter them to suit

your schedule. The Unit provides separate programming for every day of the
week- for both heating and cooling. You can override the programmed tempera-
tures for as little as one programming period or for an entire vacation.

• 

In cool weather, when the system switch is set to HEAT, the Unit will maintain
cooler “set back” room temperatures to save energy.  It will then change to
warmer “comfort” settings —  all automatically, at specified times during the day.

• 

In warm weather, when the system switch is set to COOL, the Unit will maintain
warmer “set back” room temperatures to save energy. It will then change to
cooler “comfort” settings - all automatically, at specified times during the day.

• 

A large liquid crystal display shows time, day of the week, and room and set
temperatures. It will remind you when the filter should be changed in your blower
and track your system’s energy usage. 

• 

Temperature swing adjustment lets you fine-tune your system for maximum
comfort and economy. 

• 

A 4-minute minimum on/off time in COOL prevents your air conditioning
system from being damaged.

Two Energizer® or DURACELL® “AA” alkaline batteries (not included) are
used to retain your time and temperature programs.

C

A

U

T

I

O

N

• Your thermostat is a precision instrument. Please handle it with care. 

• Turn off electricity to the appliance before installing or servicing

thermostat or any part of the system. Do not turn electricity back on

until work is completed. 

• Do not short (jumper) across electric terminals at control on furnace or

air conditioner to test the system. This will damage the thermostat and

void your warranty. 

• All wiring must conform to local codes and ordinances. 

• This thermostat is designed for use with 24 volt and millivolt systems.

The thermostat should be limited to a maximum of 1.0 amps; higher

amperage may cause damage to the thermostat. If you are in doubt,

call your utility company. 

INSTALLATION

Please read all instructions carefully before beginning installation.

TOOLS REQUIRED

#1 Phillips screwdriver (small)
Drill with 3/16-in. (4.8mm) bit

THERMOSTAT LOCATION

On replacement installations,
mount the new thermostat in
place of the old one unless the
conditions listed below suggest
otherwise. On new installations,
follow the guidelines listed below.
1. Locate the thermostat on an

inside wall, about 5 ft. (1.5m)
above the floor, and in a room that is used often. 

2. Do not install it where there are unusual heating conditions, such as: in direct 

sunlight; near a lamp, radio, television, radiator, register, or fireplace; near
hot water pipes in a wall; near a stove on the other side of a wall. 

3. Do not locate in unusual cooling conditions, such as: on a wall separating an

unheated room; or in a draft from a stairwell, door, or window. 

4. Do not locate in a damp area. This can lead to corrosion that will shorten

thermostat life.

5. Do not locate where air circulation is poor, such as: in a corner or an alcove;

or behind an open door. 

6. Do not install the unit until all construction work and painting has been

completed. 

7. This thermostat does not require leveling.

C A U T I O N

To avoid electrical shock

and to prevent damage

to the furnace, air condi-

tioner, and thermostat,

disconnect the power

supply before beginning

work. This can be done at the

fuse box, at the circuit breaker, or

at the appliance.

OFF

© COPYRIGHT 2006 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED

1

Summary of Contents for SMART TEMP PSP711RF Series






Reviews: