background image

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: info@m-system.co.jp

EM-7804-S  Rev.9  P. 1 / 21

INSTRUCTION MANUAL

PNP DISCRETE INPUT & NPN TRANSISTOR OUTPUT MODULE, 8 points each

(L

ON

W

ORKS

)

MODEL

R7L-DAC16

BEFORE USE ....

Thank you for choosing M-System.  Before use, please check 
contents of the package you received as outlined below.
If you have any problems or questions with the product, 
please contact M-System’s Sales Office or representatives.

 

PACKAGE INCLUDES:

Discrete I/O module  .......................................................... (1)
NeuronID label  .................................................................. (2)

 

MODEL NO.

Confirm Model No. marking on the product to be exactly 
what you ordered.

 

INSTRUCTION MANUAL

This manual describes necessary points of caution when 
you use this product, including installation, connection and 
basic maintenance procedures.
LNS Plug-in Software (model: R7LPLG) is usable to set up 
Functional Blocks.  For detailed information, refer to the 
R7PLG Users Manual.  The R7LPLG is downloadable at M-
System’s web site: http://www.m-system.co.jp

POINTS OF CAUTION

 

POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and 

confirm its operational range as indicated below:

    24V AC rating: 24V ±10%, 50/60 Hz, approx. 75mA
    24V DC rating: 24V ±10%, approx. 45mA

 

GENERAL PRECAUTIONS

• The unit can acquire 16 points of discrete input, also 

pulse input can be acquired up to 8 points out of 16 points.

• When counter pulse and discrete are mixed and acquired, 

make sufficient consideration to them.

• Before you remove the unit or mount it, turn off the power 

supply, input signal and output signal for safety.

 

ENVIRONMENT

• Indoor use.
• When heavy dust or metal particles are present in the 

air, install the unit inside proper housing with sufficient 
ventilation.

• Do not install the unit where it is subjected to continuous 

vibration.  Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C 

(14 to 131°F) with relative humidity within 30 to 90% RH 
in order to ensure adequate life span and operation.

 

WIRING

• Do not install cables close to noise sources (relay drive 

cable, high frequency line, etc.).

• Do not bind these cables together with those in which 

noises are present.  Do not install them in the same duct.

 

RESTRICTIONS WHEN USING LonMaker3.0 or 3.1

• Operating Environment 

   Please use LonMaker3.0 under the Environment of LNS3 

Service Pack 8 and use LonMaker3.1 under the Environ-
ment of LonMaker3.1 Service Pack 3 or later.

   Please use resource files of LonMark Resource File Ver12 

or later.

• LNS Plug-in Software is not usable. 
• The network variable of nvoCNTOut (fbCNT) is only 

SNVT_count_f.

• When registering a Device on LonMaker, please don’t use 

the following items.

  External Interface Definition / Upload From Device
  Specify Device Channel / Auto-Detect

 

AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for 
satisfying complete performance described in the data 
sheet.

Summary of Contents for R7L-DAC16






















Reviews: