(-
?I-)+DB)
?I-
)+DB)
TECHNICAL INFORMATION
8dgc`Ô\iJ\Zk`fe
Low-frequency power amplifier
Rated Power (at 1 kHz with 1% THD):
100 watts
Rated Load Impedance:
4 ohms
Rated THD (1W to –1 dB of rated power):
0.1 %
Slew Rate:
15V/µS
Distortion (THD, SMPTE IMD, DIM 100):
< 0.035%
Signal-to-Noise
(20Hz-20kHz, unweighted, referenced to 100W into 4
!
):
> 101 dB
Cooling:
Convection
Design:
Monolithic IC, Class AB,
Parametric Servo Feedback
High-frequency power amplifier
Rated Power(at 1 kHz with 1% THD):
40 watts
Rated Load Impedance:
6 ohms
Rated THD (1W to –1 dB of rated power):
0.1 %
Slew Rate:
15V/µS
Distortion (THD, SMPTE IMD, DIM 100):
< 0.035%
Signal-to-Noise
(20 Hz-20 kHz, unweighted, referenced to 40 W into 8
!
):
> 93 dB
Cooling:
Convection
Design:
Monolithic IC,
Conventional Class AB
Jpjk\dJg\Z`ÔZXk`fej
Input Type:
Balanced Differential
(XLR and 1/4" TRS)
Unbalanced (RCA)
Input Impedance:
20 k
!
Balanced
10 k
!
Unbalanced
Input Protection:
RFI and Level Protected
Maximum Input Level:
+20 dBu
Low Frequency Filter:
80 Hz, 2nd Order, Butterworth
HF Equalization:
Shelving ±2 dB @ 10 kHz
Acoustic Space:
A position:
–4 dB @ 50 Hz, shelving
B position:
–2 dB @ 50 Hz, shelving
C position:
Flat
Compressor:
Independent high and low frequency overload detection
Enclosure Alignment:
6th Order
Over Excursion Prevention: 2nd Order High-Pass Filter
Low Line Voltage Shut Down: 60% of Nominal Line
Thermal Protection:
Amplifier Shut-Down, Auto Reset
Muting:
5 seconds at turn-on
Signal Sense Threshold:
–74 dBu (0.155 mV)
Driver Protection:
Independent LF and HF Detection
Overall Compression
HR624 MK2 Specifications
<eZcfjli\
Materials and Construction:
3
⁄
4
-inch (19 mm) thick MDF cabinet construction with internal
bracing to add to cabinet stiffness.
Piano-black gloss finish.
Die-cast aluminum exponential wave guide for controlled, wide
dispersion from high-frequency driver and Zero Edge Baffle™ to
minimize diffraction around the cabinet edges.
Open cell adiabatic “foam fill” acoustical damping material ab-
sorbs internal reflections, preventing delayed sound coloration.
Flush-mount connector system allows monitor to be placed
against a wall without need for connector clearance.
KiXej[lZ\ij
Low-frequency driver:
Diameter:
6.7 inches (170mm)
Sensitivity (2.83V, 1 m):
89 dB SPL
Nominal Impedance:
4
!
Voice Coil Diameter:
1.25 inches (32mm)
Power Handling (Long Term/Program):
50/150 watts
Frequency Range:
45 Hz to 6 kHz
Frame:
Die-cast magnesium
Magnet:
Ferrite
Fully shielded:
Ferrite opposing magnet
High-frequency driver:
Sensitivity (2.83V, 1m):
91 dB SPL
Nominal Impedance:
6
!
Power Handling (Long Term/Program):
20/50 watts
Frequency Range:
1.6 kHz to 22 kHz
Diaphragm/Suspension:
Titanium with polymer suspension
Voice Coil Diameter:
1.0 inch (25.4mm)
Magnet:
Neodymium
Bucking Magnet:
Ferrite opposing magnet
Passive Radiator:
6-inch x 9-inch (152mm x 228mm) mass-loaded elliptical flat
piston with variable thickness filleted edge rubber surround.
:ifjjfm\iJ\Zk`fe
Crossover Type:
Modified Linkwitz-Riley, 24 dB/octave @ 3 kHz
