background image

T20 & T21

Top mounting
Liquid level switches

®

INSTRUCTION MANUAL AND REPLACEMENT PARTS

AGENCY APPROVALS

DESCRIPTION

T20 and T21 units are simple, reliable fl

oat switches

designed for top mounting to tanks or vessels. T20 units
utilize a single switch mechanism and float. T21 tandem
units utilize two switch mechanisms and two separate 
floats when widely spaced actuating levels are required.
T20 and T21 tandem models are available for any type of
open or closed vessel with either threaded or flanged type
mounting and actuating depths up to 1219 mm (48 inches)

OPERA

TING PRINCIPLE

A permanent magnet 

is attached to a pivoted switch

actuator 

. As the fl

oat/ displacer 

rises following the liq

-

uid level, it raises the attraction sleeve 

into the fi

eld of

the magnet, which then snaps against the non-magnetic
enclosing tube 

, actuating the switch. The enclosing tube

provides a static pressure boundary between the switch
mechanism and the process. On a falling level, an inconel
spring retracts the magnet, deactivating the switch.

pivot

return spring

rising level

falling level

UNP

ACKING

Unpack the instrument carefully

. Inspect all units for dam-

age. Report any concealed damage to carrier within 24
hours. Check the contents of the packing slip and purchase
order. Check and record the serial number for future refer-
ence when ordering parts.

Agency

Approval

ATEX

II

2G EEx d 

II 

C T6, explosion proof

II

1G EEx ia 

II 

C T6, intrinsically safe

CENELEC

EEx d 

II 

C T6, explosion proof

CCE

R1 (1) 136/MI/433, explosion proof

FM

Class 

I

, Div. 1,

Groups C & D

Class 

II

, Div. 1,

Groups E, F & G, Type NEMA 7/9

FM/CSA

Non-Hazardous area

Explosion proof area – 
Groups B, C, D, E, F & G Type NEMA 4X/7/9

SAA 

Explosion proof area

LRS

Lloyds Register of Shipment (marine applications)

GOST/

Russian Authorisation Standards

GOSGORTECHNADZOR 

Other approvals are available, consult factory for more details

For CCE approved units, use the A

TEX explosion proof model

numbers.

Consult factory for proper model numbers.

Summary of Contents for T20 Series













Reviews: