background image

Battery...........................1 or 2

*

5

Plastic carrying case.....1

*

7

C

ONCEPT AND MAIN APPLICATIONS

Model DTS141 is a cordless oil-pulse driver powered by 18V Li-ion battery

and more compact and lightweight than the current model DTS130 thanks to

the newly-developed oil unit and brushless motor.

Its other main features are:

• "T" mode: Tightening mode for self-drilling screw and bolts

• Electronic 3-stage impact power selection

  with variable power control in each range

• XPT (eXtreme Protection Technology) for use in outdoor

  applications or harsh environments

This product is compatible with 18V-1.3Ah/ 1.5Ah/ 2.0Ah/ 3.0Ah/ 4.0Ah/ 5.0Ah

Li-ion batteries BL1815/ BL1815N/ BL1820/ BL1830/ BL1840/ BL1850.

*1

 With battery BL1830/ BL1840/ BL1850

*2

 With battery BL1815/ BL1815N/ BL1820 

W

L

H

Belt clip ............................... 1                                                                                

        

Battery cover..................1

*

6

Charger ................................ 1

*

5

                        

*5

: Battery and charger are not supplied with “Z” model.

*6

: Supplied with the same quantity of extra battery.

*7

: Only for model with battery and charger.

Note:

 The standard equipment may vary by country or model variation.

S

tandard equipment

Phillips bits, Square bits, Socket bits                                                              

Battery protectors                                                                       

Four port multi charger DC18SF                                                     

Automotive charger DC18SE                                                                                               

Battery BL1820                                                                                                      

Battery BL1850

O

ptional accessories

Dimensions: mm ( " )

Length (L)

136 (5-3/8)

Width (W)

79 (3-1/8)

Height (H) 240 (9-1/2)

*

1

223 (8-3/4)

*

2

Battery

Voltage: V

18

Capacity: Ah

1.3/ 1.5/ 2.0/ 3.0/ 4.0/ 5.0

Energy capacity: Wh

24/ 27/ 36/ 54/ 72/ 90

Cell

Li-ion

Charging time (approx.): min.

15/ 15/ 24/ 22/ 36/ 45 with DC18RC

Max output (W)

280

Driving shank: mm (")

6.35mm (1/4") Hex

Capacities

Machine screw

M4 - M8 (5/32 - 5/16")

Standard bolt

M5 - M8 (3/16 - 5/16")

High tensile bolt

M5 - M6 (3/16 - 1/4")

*

3

Coarse-thread

22 - 125mm (7/8 - 4-7/8")

Impact power selection

Electronic 3 stages (Hard/ Medium/ Soft) + "T" mode

*

4

Impacts per min.:min.ˉ¹=ipm Hard/ Medium/ Soft

0 - 2,700/ 0 - 2,200/ 0 - 1,400

No load speed:min.ˉ¹=rpm

Hard/ Medium/ Soft

0 - 3,200/ 0 - 2,000/ 0 - 1,200

Max. tightening torque: N.m [ft.lbs] (in.lbs)

40 [30] (355)

Electric brake

Yes

Variable speed control by trigger

Yes

Reverse switch

Yes

LED job light

Yes

Weight according to

EPTA-Procedure 01/2003: kg(lbs)

1.2 (2.7)

*

2

/ 1.5 (3.2)

*

1

*3 

Can be used in "T" mode or soft mode. If used in medium or hard mode the tool may stop for tool body protection.

*4

 Tightening mode for self-drilling screw and bolts

Belt clip

Fast charger DC18RC

Charger DC18SD

Battery BL1815

Battery BL1830

Tool catcher

Two port multi fast charger DC18RD 

Charger DC24SC

Battery BL1815N

Battery BL1840

PRODUCT

P  1/ 11

Model No.
Description

Cordless Oil-Pulse Driver

DTS141

T

ECHNICAL INFORMATION

S

pecification

OFFICIAL USE 

for ASC & Sales Shop

Summary of Contents for DTS141












Reviews: