Makita HM1213C Technical Information Download

Page: 1 / 17

PRODUCT

P 1/ 1

ECHNICAL INFORMATION

Model No.

Description

ONCEPT AND MAIN APPLICATIONS

HM1213C, HM1203C
Demolition Hammers

Models HM1213C and HM1203C have been developed from
HM1202C series models as SDS-Max demolition hammers,
featuring high work efficiency and durability.

Listed below are specification differences between the two models.

HM1203C

Dimensions: mm (")

Width (W)

Height (H)

Length (L)

Model No.

HM1203C

HM1213C

576 (22-3/4)

149 (5-7/8)

128 (5)

265 (10-3/8)

HM1213C

Model No.

AVT (Active dynamic vibration absorber)
Vibration absorbing handle

Yes

HM1203C

HM1213C

pecification

tandard equipment

ptional accessories

Note: The standard equipment for the tool shown above may vary by country.

Continuous Rating (W)

Voltage (V)

Cycle (Hz)

Input

Output

Max. Output (W)

110
120
220
230
240

15
14

7.8
7.8
7.8

50/60
50/60
50/60
50/60
50/60

1,510

---

1,510
1,510
1,510

700
700
750
750
750

1,600
1,600
1,800
1,800
1,800

Current (A)

Model No.

HM1203C

HM1213C

Europe, Commonwealth of Dominica, Cyprus: 4.0 (13.1)

Chile, Brazil: 2.0 (6.6)

Other countries: 5.0 (16.4)

Double insulation

Power supply cord: m (ft)

Yes

10.3 (22.7)

9.2 (20.3)

10.8 (23.6)

9.7 (21.4)

Net weight: kg (lbs)

Impacts per min: min-

=ipm

Shank diameter: mm (")

950 - 1,900

Electronic
control

Variable speed control by dial

Constant speed control

Soft start

Yes
Yes
Yes

Suppression of motor speed
during no-load

Yes

18 (11/16)

Shank type

SDS-Max

Weight according to

EPTA-Procedure 01/2003

*: kg (lbs)

* includes Side handle.

Bull points
Cold chisels
Scaling chisels
Scaling chisel (for Tile)

Grooving chisel
Clay spade
Bushing tool
Rammer

Grease vessel (containing 30g hammer grease)
Plastic carrying case
Safety goggles
Hammer service kit

Side handle (D-shaped) ........... 1
Bit grease .................................. 1
Bull point .................................. 1

Plastic carrying ........................ 1
Cleaning cloth .......................... 1

Vibration
absorption

AVT

(Active dynamic

vibration absorber)

Vibration absorbing handle

Yes

Summary of Contents for HM1213C


















Search results

Summary of Contents for HM1213C

Reviews:

Related manuals for HM1213C

Brands by name

Popular brands

Makita HM1213C, Technical Information

Search results

Summary of Contents for HM1213C

Reviews:

Related manuals for HM1213C

Brands by name

Popular brands