background image

INSTALLATION INSTRUCTIONS

MANROSE CLASSIC 125mm  
EXTRACT-A-LITE FAN RANGE 

Installation Instructions

Important: The Halogen Extract-a-lite must not work independently of 
the fan.

1.   Cut a 140mm diameter hole in ceiling, (always ensure the hole is cut 

between ceiling rafters and away from any wiring or plumbing).  Fix the 
Extract-a-lite chassis using the 4 screws provided. Use the fixing clips to 
secure the fan in panel walls & ceilings.

2.  For the LED models: Connect a suitable driver to the Extract-a-Lite and 

to a suitable power supply, ideally to the switched live of the extractor 
fan installed.  Recommended driver: FAN5342. Replacement lamp: 
LHT0221.

  For the Halogen models: Connect a suitable transformer to the  

 

  Extract-a-Lite and to a suitable power supply, ideally to the switched live  
  of the extractor fan installed. Recommended transformer: FAN2101.    
  Recommended lamp: FAN0431.

3.  Place the white ceiling cover onto the Extract-a-lite chassis by positioning over 

the 3 lugs, and twisting clockwise.

4.   Never connect mains direct to the lamp.

5.  The transformer/driver must be suitable for 230V AC input. 

 

  CAUTION:  

Disconnect the power supply, and be sure that the lamp   

  has fully cooled before removing or replacing.

Fixing clip

Ceiling board

Screw

Fan

chassis

When screw is tightened fixing

clip fingers secure the fan

INSTALLATION

Thank you for selecting our Manrose 125mm Extract-a-Lite Fan Kit.
Please read all instructions before commencing installation. 

Light Specifications: 
LED models: FAN5371- FAN5372

Driver Input: 220-240 VAC
Driver Output: 12VDC 
Lamp MR16: 12V / 3W high power LED, 25

0

 beam angle

Halogen models: FAN2037 and FAN2038

Transformer Input: 220-240 VAC
Transformer Output: 12VAC 
Lamp MR16: 12V / 50W Halogen, 60

0

 beam angle

DIMENSIONS

165mm

118mm

80mm

C L A S S I C   S E R I E S

IMPORTANT  

• 

Isolate the mains supply before making any electrical connections. This system should be 
installed by a qualified electrician.

• 

When fitting through an external wall, an external grille must be fitted at all times.

• 

Fan should only be installed by fixed wiring, a flexible cord should not be used.

• 

The appliance is not intended for use by young children or infirm persons without supervision.

• 

Young children should be supervised to ensure that they do not play with the appliance.

• 

Precautions must be taken to avoid the back-flow of gases into the room from the open flue of 
gas or other open-fire appliances when mounted in outside windows or walls.

Fan Specifications:

Electrical:  220-240V  ~50Hz       
Airflow: 36l/s (130m³/hr)
Wattage: 20W
Max Temp: 50°C 
IP Rating: IPX4

Flexible 
ducting

External 
Grille

Internal 
Extract-a-Lite

The Shower Fan 
screwed to the joist

PUB0330 iss03 10/13

We reserve the right to change specification without prior warning

Manrose is proudly distributed by Simx Limited
PO Box 14 347, Panmure, Auckland, NZ.  Technical Support (09) 259 1662  
e: sales@simx.co.nz  |  www.simx.co.nz  |  www.manrose.com.au

Please ensure the corrrect LED lamp and driver OR Halogen lamp and transformer are used 
for replacements. The LED model MUST be replaced with an LED lamp and the Halogen model 
MUST be replaced with a Halogen lamp. They are not interchangeable.

Reviews: