background image

 

 

1

 

100mm/150mm SLIM LINE FAN 

Installation & Wiring Instructions 

 

FIG.1.  
 

 
 
 

FIG.2.    

 

 

 

                  FIG.3.       

 

 

 
 

 
 
 
 
 
 
 
 
FIG.4.    

 

 

 

                  FIG.5. 

 

 
 

 

 
 
 
 
 
 

 
 
 
 
 

MODEL 

VOLTAGE 

FREQUENCY 

POWER 

IP 

Hz 

F100 (1,2,3) 

220-240 

50 

16 

IP44 

 

 

 
    T 

 
 

F100S (1,2,3) 

220-240 

50 

16 

IP44 

F100T (1,2,3) 

220-240 

50 

16 

IP44 

F100TS (1,2,3) 

220-240 

50 

16 

IP44 

F100HS (1,2,3) 

220-240 

50 

16 

IP44 

F150 (1,2,3) 

220-240 

50 

16 

IPX4 

F150S (1,2,3) 

220-240 

50 

16 

IPX4 

F150T (1,2,3) 

220-240 

50 

16 

IPX4 

F150TS (1,2,3) 

220-240 

50 

16 

IPX4 

F150HS (1,2,3) 

220-240 

50 

16 

IPX4 

H models 
Humidity 
Adjustment

To activate the timer function remove jumper JP1 
(If fitted). Once removed the fan will run on for a 
fixed period of approx. 15 mins 

 

T models 
Timer 
Adjustment. 
 

Summary of Contents for SLIM F100

Page 1: ...0 16 IP44 F100TS 1 2 3 220 240 50 16 IP44 F100HS 1 2 3 220 240 50 16 IP44 F150 1 2 3 220 240 50 16 IPX4 F150S 1 2 3 220 240 50 16 IPX4 F150T 1 2 3 220 240 50 16 IPX4 F150TS 1 2 3 220 240 50 16 IPX4 F150HS 1 2 3 220 240 50 16 IPX4 H models Humidity Adjustment I To activate the timer function remove jumper JP1 If fitted Once removed the fan will run on for a fixed period of approx 15 mins T models T...

Page 2: ...F The fan should not be used where it is liable to be subject to direct water spray for prolonged periods of time G Where ducted fans are used to handle moisture laden air a condensation trap should be fitted Horizontal ducts should be arranged to slope slightly downwards away from the fan H This appliance is not intended for use by persons including children with reduced physical sensory or menta...

Page 3: ...nd cement both ends into position flush with the wall faces 2 Loosen the screw in the bottom of the grille and remove the front grille Mark the screw centres through the holes in the fan back plate Drill plug and screw into position Fix exterior grille into position with the louvres positioned downwards Note The grille must comply with the standard requirements of your country to prevent access to...

Page 4: ... the fan a fixed over run time of approx 15 mins HUMIDITY SET POINT ADJUSTMENT BEFORE ADJUSTING THE CONTROLLER SWITCH OFF THE MAINS SUPPLY HUMIDISTAT SHOULD ONLY BE ADJUSTED BEFORE OR DURING INSTALLATION 1 Remove the fan grille The controller is factory set to switch on at about 70 RH The humidity set point can be adjusted from 65 95 RH by altering the adjuster on the control PCB 2 To LOWER the se...

Reviews: