background image

OWNER’S MANUAL 

 

MODEL HST13 – AUTOTOAST™ VERTICAL TOASTER     
                              

  

 

135168CH7 RV042910 
Copyright 

©

 2010 Marshall Air Systems, Inc. 

All Rights Reserved. 

 

 

 

 

 

 

GENERAL SPECIFICATIONS 

 
 Height: 

23.250

"

 

 Width: 

19.875" 

 

Depth: 

Model CH7B-12”, CH7-15

.

250

” 

 

 

Model CH7C-12”, CH7D-12”, CH7F-12”, 

  

CH7G-12”, 

CH7H-12” 

 

Electrical: 

208V Single Phase 18.5 Amps 

 

 

240V Single Phase 21.0 Amps  

 

Power Cord: 

6 ft. 3 wire including ground, with NEMA 

 

 

L6-20Pplug (208V) (CH7C Models L6-

30p 

 

30P)(CH7H Models NEMA 6-20P) 

 

 

(Plug furnished by others on 

internationsl 

 

International units) (CH7CINTLCE 

NEMA  

 

NEMA L6-30P) 

 Weight: 

116 

lbs. 

 

Listing: 

ETL and NSF 

 
 
 
 

 
 

PRODUCT DESCRIPTION 

The Marshall High Speed Vertical Toaster produces 
a grilled effect on the cut side of the sandwich buns. 
The buns are inserted at the top of the unit and are 
pressed against a heated platen surface, which is 
covered by a replaceable toaster platen sheet.  The 
spacing between the heated grill and the conveyor is 
adjustable to accommodate different thickness of 
buns.  The buns are discharged onto a product slide 
at the bottom of the unit.  Toaster Models CH7, 
CH7B, have variable speed motor controls.  Models 
CH7C, CH7D have single speed motors.  Toast time 
on the CH7C toaster is 8 seconds heel, and 11 
seconds crown.  The CH7D toaster has a toast time 
of 23 seconds on both the crown and heel.   The 
CH7F toaster has a toast time of 9 seconds on both 
the crown and heel.  The CH7F-15 toaster has a 
toast time of 15 seconds on both the crown and heel. 
The CH7G toaster has a toast time of 3.5 minutes. 
The CH7H has a 60 second toast time.  Additionally, 
the heat settings are preset in factory, which 
eliminates unauthorized tampering. The flexibility of 
this toaster is unmatched allowing operations to 
produce the hottest buns in the shortest time.  

Supplier Name:        

MARSHALL AIR SYSTEMS, INC. 

Address:                  419 Peachtree Drive South 
                                Charlotte, NC 28217 
Serial#:                     ___________________________ 
Date Received:         ___________________________ 
Date Installed:           ___________________________ 
Telephone #:             704-525-6230 
Fax #:                        704-525-6229 
Service Referral#      800-722-3474 
Local Service Name: ___________________________ 
Local Service #:         ___________________________
Conveyor Speed 
Setting:                      ___________________________ 
 
 

 

                                                                

 

FOR YOUR SAFETY 

 

 DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF 
THIS OR ANY OTHER APPLIANCE. 
 

WARNING:

 IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, OR MAINTENANCE 

CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATION AND 
MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.
 
KEEP THIS MANUAL IN A SAFE PLACE AND RETAIN FOR FUTURE USE. 

Summary of Contents for AUTOTOAST HST13S





























Reviews: