Master Appliance Corp.
2420 18
th
St.
Racine, WI 53403-2381 USA
Tel: 262-633-7791
Email: sales@masterappliance.com
P/N 58266 REV A
PAGE 1 OF 2
Element Kits
– Part No’s. 30082, 30083, 30084, 30085, 30086, 30087, 30088
Nozzle Mounting Screw
,
(2),
not included in kit
Element
Mica
Insulator
Insert into contacts
MASTER HEAT GUN REPLACEMENT PARTS AND ACCESSORIES ARE ENGINEERED AND MANUFACTURED TO PRECISE MASTER APPLIANCE SPECIFICATIONS.
REPLACEMENT PARTS AND ACCESSORIES FROM OTHER MANUFACTURERS ARE NOT PRODUCED TO THESE PRECISE SPECIFICATIONS. FAILURE TO USE
MASTER APPLIANCE REPLACEMENT PARTS OR FAILURE TO INSTALL MASTER APPLIANCE REPLACEMENT PARTS EXACTLY AS INSTRUCTED MAY CAUSE
PHYSICAL INJURY OR DAMAGE TO THE HEAT GUN.
MASTER APPLIANCE CANNOT ASSUME RESPONSIBILITY FOR PHYSICAL INJURY OR DAMAGE TO THE HEAT GUN RESULTING FROM THE USE OF ANY OTHER
BRAND OF REPLACEMENT PART OR IMPROPER INSTALLATION OF MASTER APPLIANCE REPLACEMENT PARTS OR ACCESSORIES.
Shield,
not included in kit
Nozzle,
not included in kit
Do not touch
nozzle until cool
Contacts
in housing
New Mica Insulator
New Element
Roll mica over coils
of element
TO REMOVE OLD ELEMENT
1. Remove (2) nozzle mounting screws.
Ⓐ
2. Gently pull shield from gun housing.
3. Pull element out of housing.
TO INSTALL NEW ELEMENT
1. Gently insert new element into housing,
with contacts of element inserted fully into
spring contacts within housing.
Ⓑ
2. Wrap new mica insulator around coils of
new element, ensuring all coils are covered.
3. Gently slide nozzle straight on, aligning
ceramic element with front nozzle indents
Ⓒ
and (2) nozzle screw holes. Slide shield over
nozzle, aligning mounting holes. Install (2)
nozzle mounting screws loosely until started,
and then tighten.
Ⓐ
THIS ELEMENT KIT CONSISTS OF:
•
ELEMENT, (1)
•
MICA INSULATOR, (1)
•
RUBBER WASHER, (1)
•
BRASS NUT, #2-56, (2)
•
SCREW, PAN HEAD, #4-40, (1)
NOTE: Rubber Washer, Brass Nuts, and Screw are not used
on model numbers listed above. They are required for older
model heat guns shown on back side of this instruction sheet.
Indents support
ceramic element
Wings of ceramic
element to be
supported by
indents in nozzle
Models HG-201D, HG-201T, HG-202D, HG-202T, HG-301D,
HG-301T, HG-302D, HG-302T, HG-501D, HG-501T, HG-502D,
HG-502T, HG-801D, VT-751D, VT-752D
#2 DRIVE PHILLIPS SCREWDRIVER
TOOLS REQUIRED
If nozzle mounting screws
Ⓐ
are lost or damaged, replace only
with #6-32 steel machine screws, 3/16 inch minimum length to ½
inch maximum length.
Ⓐ
Ⓐ
Ⓒ
Ⓒ
Ⓑ
WARNING:
Failure to properly cover coils
with mica insulator could result in electrical short
WARNING:
Disconnect heat gun power cord and
allow the heat gun to cool before disassembly.
READ THE SERVICE INSTRUCTIONS CAREFULLY. FAILURE TO
EXACTLY FOLLOW THE INSTRUCTIONS COULD RESULT IN
PERSONAL INJURY OR DAMAGE TO YOUR HEAT GUN. ALL REPAIRS
MUST BE PERFORMED BY A QUALIFIED REPAIR TECHNICIAN.
