DO NOT DISCARD – GIVE TO USER
Caution: To help prevent personal injury
Made in China
to Matco specifications
•
Use of this product can expose you to chemicals
including ethylene glycol, gasoline vapors and engine
exhaust, which are known to the State of California to
cause cancer, birth defects, or reproductive harm. For
more information, visit www.P65Warnings.ca.gov.
Always wear ANSI approved safety equipment, safety
glasses and clothing when using this product. Study,
understand, and follow all instructions provided with
this product. Failure to read and follow all warnings and
operating instructions may result in damages and
serious injury or death.
• Always wear ANSI approved goggles when using this
product (users and bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with
accessories not designed for it could result in serious
injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to
perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
WARNING
INTENDED USE OF THE TOOL
Study, understand and follow all instructions provided
with this product. Read these instructions carefully
before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe, accessible place.
WEAR WORK GLOVES (RUBBER COATED PREFERRED)
FOR GRIPPING THE ADAPTER, ESPECIALLY FOR
LARGEST SIZES
. This tool is designed to be used with a
cordless drill that uses a clutch to limit torque to
different settings. Use tool to set aluminum, steel and
stainless rivet nuts up to 3/8" (10mm) in sheet metal.
Do not use this tool outside of the designed intent.
Never modify the tool for any other purpose or use.
PRODUCT INFORMATION:
1 YEAR LIMITED WARRANTY
The manufacturer warrants this product to the original user
against defective material or workmanship for a period of 1 year
from the date of purchase.
The manufacturer reserves the right to determine whether the
part or parts failed because of defective material, workmanship
or other causes. Failures caused by accident, alteration, or
misuse are not covered by this warranty.
The manufacturer, at its discretion, will repair or replace products
covered under this warranty free of charge. Repairs or
replacements of products covered under this warranty are
warrantied for the remainder of the original warranty period.
The manufacturer or its authorized service representatives must
perform all warranty repairs. Any repair to the product by
unauthorized service representatives voids this warranty. The
rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
This warranty is in lieu of all other warranties, expressed or
implied, including warranties of merchantability and fitness for a
particular purpose. Some states do not allow the exclusion or
limitations of incidental or consequential damages, so the above
limitations may not apply to you.
When unpacking, check the parts diagram and part number
listing on page 4 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
BEFORE USE
•
Adaptability.
Easily convert cordless,
pneumatic or corded drills into a power rivet
nut setter for sizes 10-24, 1/4-20, 5/16-18,
3/8-16, M5, M6, M8 and M10.
•
Versatility.
Use 12V and up cordless drills
for aluminum and steel rivet nuts, or 18V+
for larger sizes like M10 and 3/8" and/or
stainless (driver must feature torque limiting
clutch).
•
Durability.
Constructed with shielded
bearings, CRO-MO mandrels and machined
billet aluminum body.
RIVET NUT
ADAPTER KIT
RN9
Page 1
1802030-14
WARNING
