background image

1

GENUINE REAR WING

INSTALLATION AND USER’S INSTRUCTIONS

Thank you for purchasing a genuine Mazda accessory.

Before removal and installation, be sure to thoroughly read these instructions.

Please read the contents of this booklet in order to properly install and use the rear wing.

Your safety depends on it.

Keep these instructions with your vehicle records for future reference.

  There are several

 

WARNING

 

and

 

CAUTION

 

sections in this booklet concerning

safety when installing or removing the rear wing. Always read and follow them in order
to prevent injuries, accidents, and possible damage to the vehicle.

 

WARNING:

 

Indicates a situation in which serious injury or death could result if the
warning is ignored.

 CAUTION:

 

Indicates a situation in which bodily injury or damage to the vehicle
could result if the caution is ignored.

  Do not modify the rear wing.

  Do not install the rear wing in any way other than described in the following instructions.

  If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent

errors in installation.

  If you have any questions about the use of the accessory, ask your Mazda dealer for

proper advice before using it.

  Mazda and its suppliers are not responsible for injuries, accidents, and damage to

persons and property that arise from the failure of the dealer or installer to follow these
instructions.

 

To ensure safety and reliability of the work, installation, removal and disposal work must
be carried out by an Authorized Mazda Dealership.

 

Be careful not to lose removed parts, and be sure that they are kept free from scratches,
grease or other dirt.

PART NAME:

REAR WING

PART NUMBER: QSEA 51 96Z

VEHICLE:

Mazda RX-8

To the dealer

  Please turn over these instructions to the customer after installation.

To the customer

  Keep these instructions after installation. The instructions may be

 

necessary for

installing other optional parts or removal of this accessory.

 

Should the vehicle or this accessory be resold, always leave these instructions
with it for the next owner.

NOTE

 

 

WARNING

Summary of Contents for QSEA 51 96Z









Reviews: