background image

                                                                                                                                                                                                                                                                                                                 

MAIN TECH PARAMETER

           

CARE AND MAINTENANCE

 

 

MAIN TECH PARAMETER 

 

z

 

Emitting Frequency   

                          6.99KHz 
 

z

 

Signal Frequency   

                          437KHz 
 

z

 

Weight   

                          2.875KG                     
 

z

 

Power Supply 

                          8pcs 1.5V Batteries 

 
Attach external 

battery box and bag. 

 

z

 

Max Detection 
Small coil: 1.5meters 
Big coil: 3.0-3.5meters 
 
This conclusioin is elicited by 
testing an aluminum sheet 
(60cm*60cm*1cm) buried in 
dry soil 
 

z

 

Sensitivity 
Small coil: 25-30cm (test 25 US 
cent) 
Big coil: 35-40cm (test 25 US 
cent) 
 

                 
   
 

 

z

 

If the detector doesn’t work 
properly, it is possible that the 
batteries haven’t enough power, 
replace batteries to try ; 

z

 

Place batteries matching the 
polarity symbols (+ and 

) If 

you won’t use it for a long time, 
take out the batteries to avoid 
putridness; 

z

 

The search coil’s plug should be 
not affected with damp, or the 
detector will loss detection 
ability; the plug can be used 
only after drying in such 
condition; 

z

 

The detector is prohibited to 
work in rainy day and in 
burning sun; 

z

 

The search coil should be far 
away from furnace and other 
high temperature circumstance;

z

 

Each detector is attached a 
piece of guarantee

 

and it is free 

to be repaired during the length 
of warrantee unless he circuit is 
changed by user himself. 

 

 

 
 
 
 

OWENER’S MANUAL

                                               

 MD-5008 

 
 
 
Please read before using this equipment 
 
 
 

 
 
 
 

Metal Detector 

5008 

 
 
 
 
 
 
 
 
 
 
 

 
 
15 

Summary of Contents for 5008









Reviews: